Epos Speakers

Design
Epos has applied the finest wood veneers, for a high-quality finish. To minimize unwanted vibration and coloration, extensive horizontal and vertical internal bracing has been added to the sturdy 18mm MDF cabinets. For optimum performance, Elan 10 should be stand mounted.

Elan 10 is supplied with an audiophile baffle with no visible fixing screws, grille-fixing holes or cloth. The baffle is machined around the woofer to create a gently contoured horn shape and, unlike a conventional grille frame; there are no obstructions or sharp edges to cause reflections and sound colorations.

For a more family-friendly appearance and improved protection, optional cloth-covered grilles are packed in the carton. It’s simplicity itself to change them over.

Tweeter
Epos has developed a new soft-dome tweeter. By using virtual-performance CAD simulation tools, Epos has achieved very high performance with a sound which combines clarity and smoothness, in equal measure.

The new tweeter has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) doped-fabric dome, short horn, high-temperature Ferro-fluid cooled voice-coil, and shielded neodymium magnet, it is capable of high output levels for extended periods.

Mid-Bass
Epos has also developed a brand new 156mm bass/mid driver for the Elan 10. This is built on to an open-frame cast aluminium alloy chassis with a generously ventilated spider and vented magnet pole, to minimize colorations and distortions.

This bass/mid unit features a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even under high power, and help the woofer to produce a dynamic sound, with an even frequency response and smooth roll off.

The woofer is loaded by a good-sized port, flared at both ends to reduce turbulence, to produce more bass than expected from such a compact cabinet, coupled with a clear and powerful mid-range.

This mini speaker is more sensitive than you’d expect, making it suitable for use with a wide range of amplifiers, from as small as 25 watts to as large as 100 watts.

Crossover
In typical Epos fashion, the crossover is as simple as we can make it: both the woofer and tweeter networks are 2nd order filters at 3.2 kHz. To ensure the highest sound quality, all the resistors are metal oxide and the capacitors are high-quality polypropylene-foil dielectric, for their superior sound quality. Inductors are designed for low distortion even at high powers: air-core for the tweeter and an over-sized laminated-iron cored coil for the woofer. The input terminals are bi-wirable.

Detail
We paid great attention to every single minute detail during the design of the Elan 10, to give customers the best sound at the best price. It comes as no surprise that this elegant speaker will have you in awe from the first note. In addition to the astonishing bass power for its size, sound stage, depth and detail are truly exceptional, with a clarity that outshines the competition and many higher priced speakers.

This is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

This product is not eligible for discount.

Design
Epos has applied the finest wood veneers, for a high-quality finish. To minimize unwanted vibration and coloration, extensive horizontal and vertical internal bracing has been added to the sturdy 18mm MDF cabinets. For optimum performance, Elan 10 should be stand mounted.

Elan 10 is supplied with an audiophile baffle with no visible fixing screws, grille-fixing holes or cloth. The baffle is machined around the woofer to create a gently contoured horn shape and, unlike a conventional grille frame; there are no obstructions or sharp edges to cause reflections and sound colorations.

For a more family-friendly appearance and improved protection, optional cloth-covered grilles are packed in the carton. It’s simplicity itself to change them over.

Tweeter
Epos has developed a new soft-dome tweeter. By using virtual-performance CAD simulation tools, Epos has achieved very high performance with a sound which combines clarity and smoothness, in equal measure.

The new tweeter has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) doped-fabric dome, short horn, high-temperature Ferro-fluid cooled voice-coil, and shielded neodymium magnet, it is capable of high output levels for extended periods.

Mid-Bass
Epos has also developed a brand new 156mm bass/mid driver for the Elan 10. This is built on to an open-frame cast aluminium alloy chassis with a generously ventilated spider and vented magnet pole, to minimize colorations and distortions.

This bass/mid unit features a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even under high power, and help the woofer to produce a dynamic sound, with an even frequency response and smooth roll off.

The woofer is loaded by a good-sized port, flared at both ends to reduce turbulence, to produce more bass than expected from such a compact cabinet, coupled with a clear and powerful mid-range.

This mini speaker is more sensitive than you’d expect, making it suitable for use with a wide range of amplifiers, from as small as 25 watts to as large as 100 watts.

Crossover
In typical Epos fashion, the crossover is as simple as we can make it: both the woofer and tweeter networks are 2nd order filters at 3.2 kHz. To ensure the highest sound quality, all the resistors are metal oxide and the capacitors are high-quality polypropylene-foil dielectric, for their superior sound quality. Inductors are designed for low distortion even at high powers: air-core for the tweeter and an over-sized laminated-iron cored coil for the woofer. The input terminals are bi-wirable.

Detail
We paid great attention to every single minute detail during the design of the Elan 10, to give customers the best sound at the best price. It comes as no surprise that this elegant speaker will have you in awe from the first note. In addition to the astonishing bass power for its size, sound stage, depth and detail are truly exceptional, with a clarity that outshines the competition and many higher priced speakers.

This is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

This product is not eligible for discount.

Design
Epos has applied the finest wood veneers, for a high-quality finish. To minimize unwanted vibration and coloration, extensive horizontal and vertical internal bracing has been added to the sturdy 18mm MDF cabinets. For optimum performance, Elan 15 should be stand mounted. Epos make a stand to suite this and other Elan models.

Elan 15 is supplied with an audiophile baffle with no visible fixing screws, grille-fixing holes or cloth. The baffle fits snugly around the tweeter and is gently contoured around the woofer. So, unlike a conventional grille frame, there are no obstructions or sharp edges to cause reflections and sound colorations.

For a more family-friendly appearance and improved protection, optional cloth-covered grilles are packed in the carton. It’s simplicity itself to change them over.

Tweeter
Epos has developed a new soft-dome tweeter. By using virtual-performance CAD simulation tools, Epos has achieved very high performance with a sound which combines clarity and smoothness, in equal measure.

The new tweeter has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) doped-fabric dome, short horn, high-temperature Ferro-fluid cooled voice-coil, and shielded neodymium magnet, it is capable of high output levels for extended periods.

Epos has also developed a brand new 187mm bass/mid driver for the Elan 15. This is built on to an open-frame cast aluminium alloy chassis with a generously ventilated spider and vented magnet pole, to minimize colorations and distortions.

Mid-Bass
This bass/mid unit features a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even under high power, and help the woofer to produce a dynamic sound, with a very even frequency response and smooth roll off.

The woofer is loaded by a good-sized port, flared at both ends to reduce turbulence, to produce more deep, clean, detailed bass than expected from such a modest cabinet, coupled with a clear and smooth mid-range.

This medium-sized speaker is much more sensitive than you’d expect, making it suitable for use with a wide range of amplifiers, from as small as 20 watts to as large as 120 watts.

Crossover
In typical Epos fashion, the Elan 15 crossover is as simple as we can make it: both the woofer and tweeter networks are 2nd order filters at 3.2 kHz. To ensure the highest sound quality, all the resistors are metal oxide, all the capacitors are high-quality polypropylene-foil dielectric, and internal wiring is solid core. Inductors are designed for low distortion even at high powers: air-core for the tweeter and an over-sized laminated-iron cored coil for the woofer. The input terminals are bi-wirable.

Detail
We paid great attention to every single minute detail during the design of the Elan 15, to give customers the best sound at the best price. It comes as no surprise that this elegant speaker will have you in awe from the first note. In addition to the astonishing bass power for its size, sound stage, depth and detail are truly exceptional, with a clarity that outshines the competition and many higher priced speakers.

This is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

This product is not eligible for discount.

Design
Epos has applied the finest wood veneers, for a high-quality finish. To minimize unwanted vibration and coloration, extensive horizontal and vertical internal bracing has been added to the sturdy 18mm MDF cabinets. For optimum performance, Elan 15 should be stand mounted. Epos make a stand to suite this and other Elan models.

Elan 15 is supplied with an audiophile baffle with no visible fixing screws, grille-fixing holes or cloth. The baffle fits snugly around the tweeter and is gently contoured around the woofer. So, unlike a conventional grille frame, there are no obstructions or sharp edges to cause reflections and sound colorations.

For a more family-friendly appearance and improved protection, optional cloth-covered grilles are packed in the carton. It’s simplicity itself to change them over.

Tweeter
Epos has developed a new soft-dome tweeter. By using virtual-performance CAD simulation tools, Epos has achieved very high performance with a sound which combines clarity and smoothness, in equal measure.

The new tweeter has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) doped-fabric dome, short horn, high-temperature Ferro-fluid cooled voice-coil, and shielded neodymium magnet, it is capable of high output levels for extended periods.

Epos has also developed a brand new 187mm bass/mid driver for the Elan 15. This is built on to an open-frame cast aluminium alloy chassis with a generously ventilated spider and vented magnet pole, to minimize colorations and distortions.

Mid-Bass
This bass/mid unit features a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even under high power, and help the woofer to produce a dynamic sound, with a very even frequency response and smooth roll off.

The woofer is loaded by a good-sized port, flared at both ends to reduce turbulence, to produce more deep, clean, detailed bass than expected from such a modest cabinet, coupled with a clear and smooth mid-range.

This medium-sized speaker is much more sensitive than you’d expect, making it suitable for use with a wide range of amplifiers, from as small as 20 watts to as large as 120 watts.

Crossover
In typical Epos fashion, the Elan 15 crossover is as simple as we can make it: both the woofer and tweeter networks are 2nd order filters at 3.2 kHz. To ensure the highest sound quality, all the resistors are metal oxide, all the capacitors are high-quality polypropylene-foil dielectric, and internal wiring is solid core. Inductors are designed for low distortion even at high powers: air-core for the tweeter and an over-sized laminated-iron cored coil for the woofer. The input terminals are bi-wirable.

Detail
We paid great attention to every single minute detail during the design of the Elan 15, to give customers the best sound at the best price. It comes as no surprise that this elegant speaker will have you in awe from the first note. In addition to the astonishing bass power for its size, sound stage, depth and detail are truly exceptional, with a clarity that outshines the competition and many higher priced speakers.

This is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

This product is not eligible for discount.

Design
Only the finest real-wood veneers are selected, book-matched and hand-laid. Several coats of polyurethane are applied and polished for a high-quality finish. To minimise unwanted vibration and coloration, extensive horizontal and vertical internal bracing are positioned inside the sturdy 18mm thick MDF cabinets. For optimum performance and stability, they should be fitted with the plinths supplied, together with the adjustable spiked feet, designed to decouple unwanted energy from the cabinet into the floor.

The Elan 30 is supplied with two baffles. The standard audiophile baffle with no visible fixing screws is fitted. If required, this can easily be swapped for the alternative cloth covered version, which is designed with the same profile as the naked baffle. Both types of baffle fit snugly around the tweeter and are both gently contoured around the woofers. So, unlike a conventional grille frame, there are no obstructions or sharp edges to cause reflections and sound colorations. The sound from both types of baffle will therefore sound similar.

Tweeter
Epos has developed a new soft-dome tweeter for the Epic and Elan range. By using virtual-performance CAD simulation tools, this new tweeter has been designed to achieve the accuracy and speed of a metal dome but with smoothness associated with a soft dome. It has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) doped-fabric dome, short horn, high-temperature Ferro-fluid cooled voice-coil and shielded neodymium magnet, it is capable of high output levels for extended periods. Its natural high sensitivity is necessary to match the much increased output from the new bass and mid-range drivers.

Mid-Bass
A new long-throw eight-Ohm 156mm bass/mid driver has been developed for the Elan 30. Built on to an open-frame cast-aluminium alloy chassis, with a generously ventilated spider and vented magnet pole, this driver minimises colorations and distortions while allowing greater sound pressure levels than earlier Epos drivers.

The bass/mid units feature a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even at high power. This helps the woofers to produce a dynamic sound, with a very even frequency response and naturally smooth roll-off. The lower woofer is rolled-off (filtered) above 800Hz by the crossover, allowing the top mid-woofer to play bass and mid-range smoothly. The mid-woofer is rolled-off (filtered) at 3.6 kHz by the crossover to integrate properly with the tweeter. This is essentially a true 2 ½ way configuration.

Both woofers are loaded by a very large diameter port, flared at both ends, to reduce turbulence. Together they produce plenty of clean deep bass coupled with a clear, smooth and detailed mid-range.

A special feature of this floor-standing speaker is its high sensitive, making it suitable for use with a wide range of amplifiers, from as small as 12.5 Watts to as large as 150 watts into 4 Ohms. So, tube fans should find this amp a perfect match.

Crossover
In typical Epos fashion, the Elan 30 crossover is as simple as we can make it: both the woofer and tweeter networks are 2nd order filters at 800Hz and 3.6kHz. To ensure the highest sound quality, all the resistors are metal oxide, all the capacitors are high-quality polypropylene-foil dielectric types, and internal wiring uses proprietary solid-core wire covered in a sponge sheath. Inductors are designed for low distortion even at high powers: air-core for the tweeter and an over-sized laminated-iron core for the woofer. All connections to drive units and crossover are hand soldered. The input terminals are bi-wirable, using a proprietary metal terminal panel with solid metal binding post equipped for 4mm plus and large spade lugs.

Detail
We paid great attention to every single minute detail during the design of the Elan 30, to give customers the best sound at the best price. It comes as no surprise that this elegant speaker will have you in awe from the first note. In addition to the astonishing bass power, detail and depth, sound stage, depth and detail are truly exceptional, with a clarity that outshines the competition and many higher priced speakers.

This is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

This product is not eligible for discount.

Design
Only the finest real-wood veneers are selected, book-matched and hand-laid. Several coats of polyurethane are applied and polished for a high-quality finish. To minimise unwanted vibration and coloration, extensive horizontal and vertical internal bracing are positioned inside the sturdy 18mm thick MDF cabinets. For optimum performance and stability, they should be fitted with the plinths supplied, together with the adjustable spiked feet, designed to decouple unwanted energy from the cabinet into the floor.

The Elan 30 is supplied with two baffles. The standard audiophile baffle with no visible fixing screws is fitted. If required, this can easily be swapped for the alternative cloth covered version, which is designed with the same profile as the naked baffle. Both types of baffle fit snugly around the tweeter and are both gently contoured around the woofers. So, unlike a conventional grille frame, there are no obstructions or sharp edges to cause reflections and sound colorations. The sound from both types of baffle will therefore sound similar.

Tweeter
Epos has developed a new soft-dome tweeter for the Epic and Elan range. By using virtual-performance CAD simulation tools, this new tweeter has been designed to achieve the accuracy and speed of a metal dome but with smoothness associated with a soft dome. It has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) doped-fabric dome, short horn, high-temperature Ferro-fluid cooled voice-coil and shielded neodymium magnet, it is capable of high output levels for extended periods. Its natural high sensitivity is necessary to match the much increased output from the new bass and mid-range drivers.

Mid-Bass
A new long-throw eight-Ohm 156mm bass/mid driver has been developed for the Elan 30. Built on to an open-frame cast-aluminium alloy chassis, with a generously ventilated spider and vented magnet pole, this driver minimises colorations and distortions while allowing greater sound pressure levels than earlier Epos drivers.

The bass/mid units feature a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even at high power. This helps the woofers to produce a dynamic sound, with a very even frequency response and naturally smooth roll-off. The lower woofer is rolled-off (filtered) above 800Hz by the crossover, allowing the top mid-woofer to play bass and mid-range smoothly. The mid-woofer is rolled-off (filtered) at 3.6 kHz by the crossover to integrate properly with the tweeter. This is essentially a true 2 ½ way configuration.

Both woofers are loaded by a very large diameter port, flared at both ends, to reduce turbulence. Together they produce plenty of clean deep bass coupled with a clear, smooth and detailed mid-range.

A special feature of this floor-standing speaker is its high sensitive, making it suitable for use with a wide range of amplifiers, from as small as 12.5 Watts to as large as 150 watts into 4 Ohms. So, tube fans should find this amp a perfect match.

Crossover
In typical Epos fashion, the Elan 30 crossover is as simple as we can make it: both the woofer and tweeter networks are 2nd order filters at 800Hz and 3.6kHz. To ensure the highest sound quality, all the resistors are metal oxide, all the capacitors are high-quality polypropylene-foil dielectric types, and internal wiring uses proprietary solid-core wire covered in a sponge sheath. Inductors are designed for low distortion even at high powers: air-core for the tweeter and an over-sized laminated-iron core for the woofer. All connections to drive units and crossover are hand soldered. The input terminals are bi-wirable, using a proprietary metal terminal panel with solid metal binding post equipped for 4mm plus and large spade lugs.

Detail
We paid great attention to every single minute detail during the design of the Elan 30, to give customers the best sound at the best price. It comes as no surprise that this elegant speaker will have you in awe from the first note. In addition to the astonishing bass power, detail and depth, sound stage, depth and detail are truly exceptional, with a clarity that outshines the competition and many higher priced speakers.

This is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

This product is not eligible for discount.

Design
Only the finest real-wood veneers are selected, book-matched and hand-laid. Several coats of polyurethane are applied and polished for a high-quality finish. To minimise unwanted vibration and coloration, extensive horizontal and vertical internal bracing are positioned inside the sturdy 18mm thick MDF cabinets. For optimum performance and stability, they should be fitted with the plinths supplied, together with the adjustable spiked feet, designed to decouple unwanted energy from the cabinet into the floor.

Elan 35 is supplied with two baffles. The standard audiophile baffle with no visible fixing screws is fitted. If required, this can easily be swapped for the alternative cloth covered version, which is designed with the same profile as the naked baffle. Both types of baffle fit snugly around the tweeter and are both gently contoured around the woofers. So, unlike a conventional grille frame, there are no obstructions or sharp edges to cause reflections and sound colorations. The sound from both types of baffle will therefore sound similar.

Tweeter
Epos has developed a new soft-dome tweeter for the Epic and Elan range. By using virtual-performance CAD simulation tools, this new tweeter has been designed to achieve the accuracy and speed of a metal dome but with smoothness associated with a soft dome. It has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) doped-fabric dome, short horn, high-temperature Ferro-fluid cooled voice-coil and shielded neodymium magnet, it is capable of high output levels for extended periods. Its natural high sensitivity is necessary to match the much increased output from the new bass and mid-range drivers.

Mid-Bass
A new long-throw eight-Ohm 187mm bass/mid driver has been developed for the Elan 35. Built on to an open-frame cast-aluminium alloy chassis, with a generously ventilated spider and vented magnet pole, this driver minimises colorations and distortions while allowing greater sound pressure levels than earlier Epos drivers.

The bass/mid units feature a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even at high power. This helps the woofers to produce a dynamic sound, with a very even frequency response and naturally smooth roll-off. The lower woofer is rolled-off by the crossover (filtered) so that it only plays bass, allowing the top mid-woofer to play bass and mid-range smoothly. The mid-woofer is rolled-off (filtered) at higher frequencies by the crossover to integrate properly with the tweeter. This is essentially a true 2 ½ way configuration.

Both woofers are loaded by a very large diameter port, flared at both ends, to reduce turbulence. Together they produce plenty of clean deep bass coupled with a clear, smooth and detailed mid-range. In some rooms, or in placing them close to a wall or corner of a room, this may be too much, so we have supplied a custom foam bung to fit inside the entrance to the port to restrict the airflow and roll-off the bass earlier.

A special feature of this floor-standing speaker is its high sensitive, making it suitable for use with a wide range of amplifiers, from as small as 10 watts to as large as 200 watts into 4 Ohms. So, tube fans should find this amp a perfect match.

Crossover
In typical Epos fashion, the Elan 35 crossover is as simple as we can make it: both the woofer and tweeter networks are 2nd order filters at 800Hz and 3.2kHz. To ensure the highest sound quality, all the resistors are metal oxide, all the capacitors are high-quality polypropylene-foil dielectric types and internal wiring uses proprietary solid-core wire covered in a sponge sheath to prevent vibration. Inductors are designed for low distortion even at high powers: air-core for the tweeter and an over-sized laminated-iron core for the woofer. All connections to drive units and crossover are hand soldered. The input terminals are bi-wirable, using a proprietary metal terminal panel with solid metal binding post equipped for 4mm plus and large spade lugs.

Detail
We paid great attention to every single minute detail during the design of the Elan 35, to give customers the best sound at the best price. It comes as no surprise that this elegant speaker will have you in awe from the first note. In addition to the astonishing bass power, detail and depth, sound stage, depth and detail are truly exceptional, with a clarity that outshines the competition and many higher priced speakers.

This is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

This product is not eligible for discount.

Design
Only the finest real-wood veneers are selected, book-matched and hand-laid. Several coats of polyurethane are applied and polished for a high-quality finish. To minimise unwanted vibration and coloration, extensive horizontal and vertical internal bracing are positioned inside the sturdy 18mm thick MDF cabinets. For optimum performance and stability, they should be fitted with the plinths supplied, together with the adjustable spiked feet, designed to decouple unwanted energy from the cabinet into the floor.

Elan 35 is supplied with two baffles. The standard audiophile baffle with no visible fixing screws is fitted. If required, this can easily be swapped for the alternative cloth covered version, which is designed with the same profile as the naked baffle. Both types of baffle fit snugly around the tweeter and are both gently contoured around the woofers. So, unlike a conventional grille frame, there are no obstructions or sharp edges to cause reflections and sound colorations. The sound from both types of baffle will therefore sound similar.

Tweeter
Epos has developed a new soft-dome tweeter for the Epic and Elan range. By using virtual-performance CAD simulation tools, this new tweeter has been designed to achieve the accuracy and speed of a metal dome but with smoothness associated with a soft dome. It has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) doped-fabric dome, short horn, high-temperature Ferro-fluid cooled voice-coil and shielded neodymium magnet, it is capable of high output levels for extended periods. Its natural high sensitivity is necessary to match the much increased output from the new bass and mid-range drivers.

Mid-Bass
A new long-throw eight-Ohm 187mm bass/mid driver has been developed for the Elan 35. Built on to an open-frame cast-aluminium alloy chassis, with a generously ventilated spider and vented magnet pole, this driver minimises colorations and distortions while allowing greater sound pressure levels than earlier Epos drivers.

The bass/mid units feature a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even at high power. This helps the woofers to produce a dynamic sound, with a very even frequency response and naturally smooth roll-off. The lower woofer is rolled-off by the crossover (filtered) so that it only plays bass, allowing the top mid-woofer to play bass and mid-range smoothly. The mid-woofer is rolled-off (filtered) at higher frequencies by the crossover to integrate properly with the tweeter. This is essentially a true 2 ½ way configuration.

Both woofers are loaded by a very large diameter port, flared at both ends, to reduce turbulence. Together they produce plenty of clean deep bass coupled with a clear, smooth and detailed mid-range. In some rooms, or in placing them close to a wall or corner of a room, this may be too much, so we have supplied a custom foam bung to fit inside the entrance to the port to restrict the airflow and roll-off the bass earlier.

A special feature of this floor-standing speaker is its high sensitive, making it suitable for use with a wide range of amplifiers, from as small as 10 watts to as large as 200 watts into 4 Ohms. So, tube fans should find this amp a perfect match.

Crossover
In typical Epos fashion, the Elan 35 crossover is as simple as we can make it: both the woofer and tweeter networks are 2nd order filters at 800Hz and 3.2kHz. To ensure the highest sound quality, all the resistors are metal oxide, all the capacitors are high-quality polypropylene-foil dielectric types and internal wiring uses proprietary solid-core wire covered in a sponge sheath to prevent vibration. Inductors are designed for low distortion even at high powers: air-core for the tweeter and an over-sized laminated-iron core for the woofer. All connections to drive units and crossover are hand soldered. The input terminals are bi-wirable, using a proprietary metal terminal panel with solid metal binding post equipped for 4mm plus and large spade lugs.

Detail
We paid great attention to every single minute detail during the design of the Elan 35, to give customers the best sound at the best price. It comes as no surprise that this elegant speaker will have you in awe from the first note. In addition to the astonishing bass power, detail and depth, sound stage, depth and detail are truly exceptional, with a clarity that outshines the competition and many higher priced speakers.

This is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

This product is not eligible for discount.

Each and every part of the Epos Encore 50 has been developed by Epos engineers to a standard not previously achieved by the company. From the original design concept through to the cabinet construction, speaker drive units, crossover and final voicing, the Encore 50 stands superior in every way.

Cabinet
It is tall and imposing yet exhibits elegance synonymous with Epos. Standing 1.2 metres high, it is deeper rather than wide and is supplied with a strong stylish painted MDF plinth to support its 50 kg weight and spread its footprint for improved stability and mechanical decoupling. Fully adjustable turned aluminium and steel spiked feet can raise or lower the speaker to adjust or tilt the level. The cabinet itself is made from a composite of birch-plywood and MDF which has been extensively strengthened internally using plywood bracing within the mid-range and bass enclosures.

To ensure the lowest colouration, the cabinet and bracing have been optimised, following accelerometer measurements and listening tests. Hand selected and book-matched real wood veneer has been chosen give the most luxurious finish on an Epos speaker so far.

Separate Bass, Mid-range and Crossover sections of the cabinet are hermetically sealed and allow the Crossover to be located in a convenient section at the bottom of the cabinet, accessed via the large, ventilated terminal panel on the bottom rear with a letter box opening in the plinth. All drive units are separately wired to the crossover section, using custom Epos solid core wire.

The bass enclosure has a volume of 43 litres. Two 220mm woofers are bass-reflex loaded by one large diameter 90mm port, positioned mid-way between the woofers and flared at both ends to minimise port turbulence and harmonic distortion. The height and spacing of the woofers has been chosen to minimise the ‘floor-bounce’ cancellation, optimise bass output and ensure a smooth bass-mid range transition in room. The mid-range unit is in its own, braced, 8 litre sealed-box enclosure.

Drive Units
The 2 x 220 mm woofers and 158 mm mid-range cones are made from a Kevlar/carbon fibre/pulp mixture to combine high rigidity, with good inherent damping and feature concave dust caps coupled tightly to the cone. Frequency responses of both woofer and mid-range are inherently very smooth. They each incorporate a copper shorting ring in the magnetic circuit to reduce and linearise inductance and therefore, reduce harmonic and inter-modulation distortions at high sound pressure levels. The two woofer cones couple acoustically at low frequencies and are port loaded for extremely high power handling.

The tweeter is a specially developed version of the Epos Mi tweeter, with anodised aluminium dome, Kapton voice coil former, braided lead-out wires and Ferro-Fluid damping. The centre pole is damped under the dome and vented into a contoured, felt-filled, rear chamber to damp the fundamental resonance frequency.

Crossover
The crossover design of the Epos Encore 50 is revolutionary. It allows the user unparalleled flexibility to compensate for individual room acoustics, without compromising sound quality in any way. The tonal balance of the speaker may be easily changed by the user to increase or decrease the tweeter and midrange output in 1.5dB steps, via an aperture in the bottom of the speaker and plinth. The crossovers use high-grade customised ‘Epos’ polypropylene capacitors and non-polarised electrolytic capacitors, which are bypassed with polypropylene capacitors on the mid-range and tweeter. It also uses air-core inductors, a tapped autotransformer for adjusting the mid-range output and laminated steel-core inductors. Metal-oxide resistors are paralleled where necessary to achieve high power rating and a custom heatsink is used to reduce the temperature.

The high sensitivity mid-range is attenuated by a tapped auto transformer, which doubles as the high-pass crossover inductor. The tweeter network also has variable attenuation via metal-oxide resistors. The maximum sensitivity treble position by-passes all attenuation. Passive components are mounted on a high quality, glass fibre PCB, mechanically isolated from the cabinet.

The crossover PCB’s are designed to be completely, or partially, by-passed, to enable the user to configure the speaker in passive or active mode. Epos, will offer a custom DAC with programmable digital crossover to suit any make of amplification system. In short, it has unparalleled flexibility.

The ongoing development for a future user upgrade to the Epos Encore 50 will represent yet another great leap forward in Epos speaker design and will have music lovers giving it a ‘standing ovation’ whilst applauding this exceptional speaker.

Plinth
A custom made MDF plinth helps to extend the footprint of the speaker and decouple mechanical vibrations from the cabinet. This makes the speaker more stable in a domestic environment and improves low frequency performance.

It also allows access to the crossover adjustment patch-board. Adjustable metal feet allow the height and angle of the speaker to be adjusted. This enables a custom skateboard to fit underneath so the speaker can be transported on wheels to a different position and then carefully lowered into place. This is supplied with the speakers.

This product is not eligible for discount.

At first glance, the Epic range harks back to an 80’s look, but with a modern twist. Epos uses a high-quality vinyl wood veneer to produce a high-end appearance whilst keeping the Epic’s entry-level price point in mind.

Design
Uniquely, its front baffle design presents two surprisingly different faces. Straight out of the box the Epic 1 is supplied with an audiophile baffle with no visible fixing screws, grille-fixing holes or cloth. The baffle is machined around the woofer to create a gently contoured horn shape and, unlike a conventional grille frame; there are no added obstructions or sharp edges to cause reflections and sound colorations.

In the carton you will also find an optional cloth-covered grille. For those who don’t like looking at loudspeaker drivers, this is the ideal compromise. The spare grille has the same audible reflection-free advantages found in the ‘audiophile’ baffle, but elegantly hides the drivers under a fine acoustically transparent cloth, providing protection to the more delicate parts of the speaker.

The baffle on the Epic 1 can be changed in a unique way. The Illustration shows the baffle removal tool in use. With light pressure, the front baffle will detach allowing you to swap it as and when required.

Tweeter
Epos developed a new soft-dome tweeter for Epic – quite a landmark – because this is the first soft-dome tweeter used in the history of the company. By using virtual performance CAD simulation tools, Epos has achieved very high performance, and a clean, open yet smooth sound quality which hits well above the tweeter’s price point.

The new tweeter has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) fabric-dome, short horn, high-temperature ferro-fluid cooled voice-coil, and shielded neodymium magnet, it is capable of high output levels for extended periods without degradation to sound quality or itself.

Mid Bass
Epos has also developed a brand new 150mm (5 ¼ inch) driver for the Epic 1, which produces an even frequency response and smooth roll off. This woofer/mid has a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even under high power. The woofer is loaded by a good-sized port, flared at both ends to reduce turbulence, to produce more bass than expected from such a compact cabinet, coupled with a clear and powerful mid-range.

This mini speaker is more sensitive than you’d expect, making it suitable for use with a wide range of amplifiers, from as small as 20 watts to as large as 100 watts.

Crossover
In typical Epos fashion, the Epic 1 crossover is as simple as we can make it: both the woofer and tweeter networks are 2nd order filters. To ensure high sound quality, all the resistors are metal oxide – a type rarely found in products at this price level. Also included are high-quality polypropylene capacitors, chosen for their superior sound quality. Inductors are designed for low distortion even at high powers: air-core for the tweeter and an over-sized laminated-iron cored coil for the woofer. The input terminals are gold plated and bi-wirable. It’s all in keeping with the Epos ethos of high quality at sensible prices, even for this entry-level speaker.

This same ethos influences every part of the Epic 1, down to the extensive horizontal and vertical internal bracing and rigid 18mm MDF cabinet, far in excess of typical rivals. Just pick it up to feel the weight. For optimum performance, it should be stand-mounted. Epos recommends its ST35.

Detail
We paid great attention to every single minute detail during the design of the Epic 1, to give customers the best sound at the best price. It comes as no surprise that this little speaker will have you in awe from the first note. The level of sound stage, depth and detail is truly exceptional, with a clarity that outshines the competition and even some higher priced speakers.

The Epic 1 is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

Standsold separately.

This product is not eligible for discount.

At first glance, the Epic range harks back to an 80’s look, but with a modern twist. Epos uses a high-quality vinyl wood veneer to produce a high-end appearance whilst keeping the Epic’s entry-level price point in mind.

Uniquely, its front baffle design presents two surprisingly different faces. Straight out of the box the Epic 1 is supplied with an audiophile baffle with no visible fixing screws, grille-fixing holes or cloth. The baffle is machined around the woofer to create a gently contoured horn shape and, unlike a conventional grille frame; there are no added obstructions or sharp edges to cause reflections and sound colorations.

In the carton you will also find an optional cloth-covered grille. For those who don’t like looking at loudspeaker drivers, this is the ideal compromise. The spare grille has the same audible reflection-free advantages found in the ‘audiophile’ baffle, but elegantly hides the drivers under a fine acoustically transparent cloth, providing protection to the more delicate parts of the speaker.

The baffle on the Epic 1 can be changed in a unique way. The Illustration shows the baffle removal tool in use. With light pressure, the front baffle will detach allowing you to swap it as and when required.

The new tweeter has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) fabric-dome, short horn, high-temperature ferro-fluid cooled voice-coil, and shielded neodymium magnet, it is capable of high output levels for extended periods without degradation to sound quality or itself.

This product is not eligible for discount.

At first glance, the Epic range harks back to an 80’s look, but with a modern twist. Epos uses a high-quality vinyl wood veneer to produce a high-end appearance whilst keeping the Epic’s entry-level price point in mind.

Design
Uniquely, the front baffle presents two surprisingly different faces. Straight out of the box, the Epic 2 is supplied with an audiophile baffle with no visible fixing screws, grille-fixing holes or cloth. The baffle is machined around the woofer to create a gently contoured horn shape and, unlike a conventional grille frame; there are no added obstructions or sharp edges to cause reflections and sound colorations.

In the carton, you will also find an optional cloth-covered grille. For those who don’t like looking at loudspeaker drivers, this is the ideal compromise. The spare grille has the same audible reflection-free advantages found in the ‘audiophile’ baffle, but elegantly hides the drivers under a fine acoustically transparent cloth, providing protection to the more delicate parts of the speaker.

The front baffle on the Epic 2 can be changed in a unique way. The Illustration shows the baffle removal tool in use. With light pressure, the baffle will detach, allowing you to swap it as and when required.

Tweeter
Epos developed a new soft-dome tweeter for Epic – quite a landmark – because this is the first soft-dome tweeter in the history of the company. By using virtual performance CAD simulation tools, Epos has achieved very high performance, and a clean, open yet smooth sound quality which hits well above the tweeter’s price point.

The new tweeter has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) fabric-dome, short horn, high-temperature Ferro-fluid cooled voice-coil, and shielded neodymium magnet, it is capable of high output levels for extended periods without degradation to sound quality or itself.

Mid Bass
Epos has also developed a brand new 179mm (6 1/2 inch) 4 Ohm driver for the Epic 2, which produces an even frequency response and smooth roll-off. This has a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even under high power operation. The woofer is loaded at low frequencies, using a large-diameter port, flared at both ends to avoid turbulence that produces surprising levels and depths of good clean bass for the speaker’s size, coupled with a clear and open mid-range.

The Epic 2 is a surprisingly sensitive speaker with high power handling, making it suitable for use with a wide range of amplifiers, from as small as 20 watts to as large as 120 watts.

Crossover
In typical Epos fashion, the Epic 2 crossover is as simple as we can make it: The woofer/mid and tweeter networks are 2nd order filters. To ensure high sound quality, all the resistors are metal oxide – a type rarely found in products at this price level. Also included are high-quality polypropylene capacitors, used for their superior sound quality. Inductors are designed for low distortion even at high powers: air-core for the tweeter and over-sized laminated-iron core for the woofer. The input terminals are gold plated and bi-wirable. It’s all in keeping with the Epos ethos of providing high quality at sensible prices.

This same ethos influences every part of the Epic 2, down to the extensive vertical and horizontal internal bracing and rigid 18mm MDF cabinet, far in excess of typical rivals. Just pick it up to feel the weight. For best performance, the speaker should be stand mounted. Epos recommends the ST12i stand.

Detail
We paid great attention to every single minute detail during the design of the Epic 2, to give customers the best sound at the best price. It comes as no surprise that this compact speaker will have you in awe from the first note. In addition to the surprising bass power and quality, the sound stage, depth and detail are exceptional, with a clarity that outshines the completion and many higher priced speakers. It is indeed a very engaging loudspeaker with a fine all-round performance.

The Epic 2 is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

Stand sold separately.

This product is not eligible for discount.

At first glance, the Epic range harks back to an 80’s look, but with a modern twist. Epos uses a high-quality vinyl wood veneer to produce a high-end appearance whilst keeping the Epic’s entry-level price point in mind.

Design
Uniquely, the front baffle presents two surprisingly different faces. Straight out of the box, the Epic 2 is supplied with an audiophile baffle with no visible fixing screws, grille-fixing holes or cloth. The baffle is machined around the woofer to create a gently contoured horn shape and, unlike a conventional grille frame; there are no added obstructions or sharp edges to cause reflections and sound colorations.

In the carton, you will also find an optional cloth-covered grille. For those who don’t like looking at loudspeaker drivers, this is the ideal compromise. The spare grille has the same audible reflection-free advantages found in the ‘audiophile’ baffle, but elegantly hides the drivers under a fine acoustically transparent cloth, providing protection to the more delicate parts of the speaker.

The front baffle on the Epic 2 can be changed in a unique way. The Illustration shows the baffle removal tool in use. With light pressure, the baffle will detach, allowing you to swap it as and when required.

Tweeter
Epos developed a new soft-dome tweeter for Epic – quite a landmark – because this is the first soft-dome tweeter in the history of the company. By using virtual performance CAD simulation tools, Epos has achieved very high performance, and a clean, open yet smooth sound quality which hits well above the tweeter’s price point.

The new tweeter has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) fabric-dome, short horn, high-temperature Ferro-fluid cooled voice-coil, and shielded neodymium magnet, it is capable of high output levels for extended periods without degradation to sound quality or itself.

Mid Bass
Epos has also developed a brand new 179mm (6 1/2 inch) 4 Ohm driver for the Epic 2, which produces an even frequency response and smooth roll-off. This has a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even under high power operation. The woofer is loaded at low frequencies, using a large-diameter port, flared at both ends to avoid turbulence that produces surprising levels and depths of good clean bass for the speaker’s size, coupled with a clear and open mid-range.

The Epic 2 is a surprisingly sensitive speaker with high power handling, making it suitable for use with a wide range of amplifiers, from as small as 20 watts to as large as 120 watts.

Crossover
In typical Epos fashion, the Epic 2 crossover is as simple as we can make it: The woofer/mid and tweeter networks are 2nd order filters. To ensure high sound quality, all the resistors are metal oxide – a type rarely found in products at this price level. Also included are high-quality polypropylene capacitors, used for their superior sound quality. Inductors are designed for low distortion even at high powers: air-core for the tweeter and over-sized laminated-iron core for the woofer. The input terminals are gold plated and bi-wirable. It’s all in keeping with the Epos ethos of providing high quality at sensible prices.

This same ethos influences every part of the Epic 2, down to the extensive vertical and horizontal internal bracing and rigid 18mm MDF cabinet, far in excess of typical rivals. Just pick it up to feel the weight. For best performance, the speaker should be stand mounted. Epos recommends the ST12i stand.

Detail
We paid great attention to every single minute detail during the design of the Epic 2, to give customers the best sound at the best price. It comes as no surprise that this compact speaker will have you in awe from the first note. In addition to the surprising bass power and quality, the sound stage, depth and detail are exceptional, with a clarity that outshines the completion and many higher priced speakers. It is indeed a very engaging loudspeaker with a fine all-round performance.

The Epic 2 is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

Stand sold separately.

This product is not eligible for discount.

The Epic 5 is the elegant floor-standing model in this new range of loudspeakers from Epos. This 2 1/2 way design holds true to Epos’s purist principles of simple crossover, well-behaved drive units and clean understated aesthetics yet delivers a big-speaker performance way above its price point.

At first glance, the Epic range harks back to an 80’s look, but with a modern twist. Epos uses a high-quality vinyl wood veneer to produce a high-end appearance whilst keeping the Epic’s entry-level price point in mind.

Design
Uniquely, the top section of its front baffle presents two surprisingly different faces. Straight out of the box the Epic 5 is supplied with an audiophile baffle with no visible fixing screws, grille-fixing holes or cloth. The baffle is machined around the woofer to create a gently contoured horn shape and, unlike a conventional grille frame; there are no added obstructions or sharp edges to cause reflections and sound colorations.

In the carton you will also find an optional cloth-covered grille. For those who don’t like looking at loudspeaker drivers, this is the ideal compromise. The spare grille has the same audible reflection-free advantages found in the ‘audiophile’ baffle, but elegantly hides the drivers under a fine acoustically transparent cloth, providing protection to the more delicate parts of the speaker.

The top section of the front baffle of the Epic 5 can be changed in a unique way. The Illustration shows the baffle removal tool in use. With light pressure, the topmost part of the front baffle will detach, allowing you to swap it as and when required.

Tweeter
Epos developed a new soft-dome tweeter for Epic – quite a landmark, because this is the first soft-dome tweeter in the history of the company. By using virtual performance CAD simulation tools, Epos has achieved very high performance, and a clean, open yet smooth sound quality which hits well above the tweeter’s price point.

The new tweeter has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) fabric-dome, short horn, high-temperature ferro-fluid cooled voice-coil, and shielded neodymium magnet, it is capable of high output levels for extended periods without degradation to sound quality or itself.

Mid Bass
Epos has also developed a brand new 179mm (6 1/2 inch) 8 Ohm driver for the Epic 5, which produces an even frequency response and smooth roll off. This has a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even under high power operation. The two woofers operate in parallel at low frequencies to produce astonishing levels and depths of bass, while the lower woofer is rolled off gently above a few hundred Hz, leaving the upper drive unit to work as a mid-range. Both woofers at loaded at low frequencies, using a very large diameter port, flared at both ends to avoid turbulence.

The Epic 5 is a very sensitive 4 Ohm speaker with clear and powerful mid-range, very strong bass and high power handling, making it suitable for use with a wide range of amplifiers, from as small as 20 watts to as large as 200 watts.

Crossover
In typical Epos fashion, the Epic 5 crossover is as simple as we can make it: The woofer, woofer/mid and tweeter networks are all 2nd order filters. To ensure high sound quality, resistors in the tweeter and upper mid/woofer networks are metal oxide – a type rarely found in products at this price level. Also included are high-quality polypropylene capacitors, used for their superior sound quality. Inductors are designed for low distortion even at high powers: air-core for the tweeter and over-sized laminated-iron core for both woofers. The input terminals are gold plated and bi-wirable. It’s all in keeping with the Epos ethos of providing high quality at sensible prices.

This same ethos influences every part of the Epic 5, down to the very extensive vertical and horizontal internal bracing and rigid 18mm MDF cabinet, far in excess of typical rivals. Just pick it up to feel the weight. For enhanced stability and sound quality, a neat, contoured MDF plinth is included, complete with adjustable spikes.

Detail
We paid great attention to every single minute detail during the design of the Epic 5, to give customers the best sound at the best price. It comes as no surprise that this elegant speaker will have you in awe from the first note. In addition to the astonishing bass power, detail and depth, sound stage, depth and detail are truly exceptional, with a clarity that outshines the competition and many higher priced speakers.

The Epic 5 is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

This product not eligible for discount.

The Epic 5 is the elegant floor-standing model in this new range of loudspeakers from Epos. This 2 1/2 way design holds true to Epos’s purist principles of simple crossover, well-behaved drive units and clean understated aesthetics yet delivers a big-speaker performance way above its price point.

At first glance, the Epic range harks back to an 80’s look, but with a modern twist. Epos uses a high-quality vinyl wood veneer to produce a high-end appearance whilst keeping the Epic’s entry-level price point in mind.

Design
Uniquely, the top section of its front baffle presents two surprisingly different faces. Straight out of the box the Epic 5 is supplied with an audiophile baffle with no visible fixing screws, grille-fixing holes or cloth. The baffle is machined around the woofer to create a gently contoured horn shape and, unlike a conventional grille frame; there are no added obstructions or sharp edges to cause reflections and sound colorations.

In the carton you will also find an optional cloth-covered grille. For those who don’t like looking at loudspeaker drivers, this is the ideal compromise. The spare grille has the same audible reflection-free advantages found in the ‘audiophile’ baffle, but elegantly hides the drivers under a fine acoustically transparent cloth, providing protection to the more delicate parts of the speaker.

The top section of the front baffle of the Epic 5 can be changed in a unique way. The Illustration shows the baffle removal tool in use. With light pressure, the topmost part of the front baffle will detach, allowing you to swap it as and when required.

Tweeter
Epos developed a new soft-dome tweeter for Epic – quite a landmark, because this is the first soft-dome tweeter in the history of the company. By using virtual performance CAD simulation tools, Epos has achieved very high performance, and a clean, open yet smooth sound quality which hits well above the tweeter’s price point.

The new tweeter has a low resonance frequency, high sensitivity and extended high frequency response. With its 25mm (one inch) fabric-dome, short horn, high-temperature ferro-fluid cooled voice-coil, and shielded neodymium magnet, it is capable of high output levels for extended periods without degradation to sound quality or itself.

Mid Bass
Epos has also developed a brand new 179mm (6 1/2 inch) 8 Ohm driver for the Epic 5, which produces an even frequency response and smooth roll off. This has a high-quality polypropylene cone and ‘bullet’-shaped dust cap. These form a stiff yet pliable, well-damped structure which retains its shape, even under high power operation. The two woofers operate in parallel at low frequencies to produce astonishing levels and depths of bass, while the lower woofer is rolled off gently above a few hundred Hz, leaving the upper drive unit to work as a mid-range. Both woofers at loaded at low frequencies, using a very large diameter port, flared at both ends to avoid turbulence.

The Epic 5 is a very sensitive 4 Ohm speaker with clear and powerful mid-range, very strong bass and high power handling, making it suitable for use with a wide range of amplifiers, from as small as 20 watts to as large as 200 watts.

Crossover
In typical Epos fashion, the Epic 5 crossover is as simple as we can make it: The woofer, woofer/mid and tweeter networks are all 2nd order filters. To ensure high sound quality, resistors in the tweeter and upper mid/woofer networks are metal oxide – a type rarely found in products at this price level. Also included are high-quality polypropylene capacitors, used for their superior sound quality. Inductors are designed for low distortion even at high powers: air-core for the tweeter and over-sized laminated-iron core for both woofers. The input terminals are gold plated and bi-wirable. It’s all in keeping with the Epos ethos of providing high quality at sensible prices.

This same ethos influences every part of the Epic 5, down to the very extensive vertical and horizontal internal bracing and rigid 18mm MDF cabinet, far in excess of typical rivals. Just pick it up to feel the weight. For enhanced stability and sound quality, a neat, contoured MDF plinth is included, complete with adjustable spikes.

Detail
We paid great attention to every single minute detail during the design of the Epic 5, to give customers the best sound at the best price. It comes as no surprise that this elegant speaker will have you in awe from the first note. In addition to the astonishing bass power, detail and depth, sound stage, depth and detail are truly exceptional, with a clarity that outshines the competition and many higher priced speakers.

The Epic 5 is a truly eye and ear-opening loudspeaker that will keep you enthralled listening to your favorite tracks for many years to come.

This product not eligible for discount.

Designed specifically to accommodate the Epos M12i bookshelf speakers, the ST12i metal stand is both elegant and functional and is available only in a durable black paint finish. Needless to say, they are able to be used with any make of bookshelf speaker, not just Epos. They are narrower than the earlier square section ST12 open frame stands, which suited the M12 speaker.

Their performance particularly improves the bass performance of the M12i and their open frame design helps to build an exceptional sound stage, with no shortage of presence. They are dynamic and solid and designed to be acceptable in most domestic settings.

The ST12i speaker support stands 51 cm high without spikes. The top mounting area is constructed as an open frame made from four 3mm thick straps producing a top plate area measuring 24 x 17.5 cm, with rounded edges to match the 35mm columns. The solid 4mm bottom plate also has rounded edges and features an Epos badge at the front. Four 35mm diameter heavy gauge steel columns make up the supports. The construction is specifically designed to create similar performance to the original open frame ST12 stand, but which is cosmetically more attractive. It is made this way to help build an even more transparent sound stage than a stand with a heavy centre column. They do not get in the way of the music.

The ST12i is not designed to allow sand to be added to the columns. They are supplied in a self-assembly format complete with optional top and bottom spikes, that are adjustable.

This product not eligible for discount.

Designed to accommodate the smaller Epos bookshelf speakers – like the new ELS 8 and M5i, the ST35 metal stand is both elegant and functional and is available in a choice of either black or silver. Their performance particularly improves the bass performance of small speakers and their open frame design helps to build an exceptional sound stage, with no shortage of presence. They are dynamic and solid and designed to be acceptable in most domestic settings.

The ST35 speaker support stands 58.5 cm high and has a solid 4mm thick top plate. It has a solid 4mm bottom plate which is rounded on the front edge and tapered at the back and features an Epos badge at the front. Three heavy gauge steel columns make up the supports, the larger of which has the added advantage of a discreet cable management channel.

The ST35 does not allow sand to be added to the columns. They are supplied in a self-assembly format complete with optional top and bottom spikes, that are adjustable.

This product not eligible for discount.