Have a question about this product? Please email ouraudio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.
Marrying a gorgeous sounding tube pre-amp with solid-state amplification has been a technique for achieving unequaled sound quality in hi-end component audio since the advent of the transistor. While kicking around ideas for our new headphone amp we thought, why not try this same technique in a single component? We built one up and were blown away by the increased detail, clarity, and presence the design offered. The tube hybrid headphone amp was born. Hand assembled using the highest quality parts available the music hall ph25.2 will have you singing along with your favorite artists.
Upgrade the original coned feet on any Scout, Scoutmaster, Super Scoutmaster and Aries Series turntables ever made with the new VPI Mini HR-X Replacement Feet! These heavier and more stable composite HR-X Style Feet provide greater stability, vibration control and better sound.
This is one of the best, most affordable and easiest to install upgrades VPI has ever made. Just unscrew your existing coned feet and screw in your new VPI Mini HR-X Feet to take your turntable one step closer in sound to VPI's flagship model the VPI HR-X!
The VPI Mini HR-X Feet fit almost exactly inside the dimensions of your Scout, Scoutmaster, Super Scoutmaster or Aries Plinths which means no incompatibility with dustcovers and the like!
The VPI Mini HR-X Feet are quite heavy (almost 1 pound per foot), well isolated and have a very stable 2 1/2' diameter footprint! They are made of a composite of Delrin and Stainless Steel similar the plinth of the highly acclaimed VPI HR-X. They also have a damping mechanism integrated into the design as well. The bottom of the feet have 3 steel ball bearings that are the contact point with your stand to further minimize vibration. The result of all these design features is a lower noise floor, tighter bass and improved overall clarity and soundstage for your VPI turntable.
Easy to use and install! Just unscrew the existing coned feet beneath your plinth and replace them with the VPI Mini HR-X Feet!
The TNT HRX Top Plate is a 3” thick MDF with black oak on all four sides, black semi-gloss Formica on the top, and a cutout and isolation system for the HR-X dual motor assembly. The VPI TNT HRX Top Plate can be combined with the Turntable Stand for the ultimate combination sound quality!
The VPI turntable stand is composed of a welded steel base section 30” high with spiked leveling feet. The four columns are hollow and can be filled with sand or zing shot for better damping. Three welded cross bar shelves allow the placement of SDS, phono section, and preamp or any combination of equipment you might want to use.
This complete system levels, supports, and isolates, any turntable on the market in a stable and attractive manner!
VPI HRX Top Plate Dimensions:
VPI Turntable Stand (Not Included):
Adjustable 30” high
The Hunt EDA record cleaning brush contains over 1,000,000 anti static carbon fibers. The fibers are in two rows with a static grounding pad centered between. The grounding pad supports the tiny carbon fibers and keeps them erect so they can dig down deep into the groove and extract trapped dust. Look at a record. It contains microscopic undulations inside the groove wall smaller than a human hair that the naked eye cannot see. This is how music is stored on an LP. And this is why fat pads will not do. A fat pad can't get down into the groove. It simply brushes over the top and removes the surface dust. The real culprit is the dust that's trapped deep in the record groove. The only way to remove this dust is with the Hunt EDA. It's super easy to use. Don't push it down on the record simply support the back of the brush with your hand and let the brush's weight do the work. You want to keep those bristles erect not rolled over. The Hunt EDA comes with it's own support stand which also doubles as a cleaning tool. Slide the stand back and forth across the carbon fiber bristles to remove the dust. This will keep the carbon fibers clean and free from your messy hand oils. Use alone or ideally with a Zerostat gun. First, destat the record with the gun then use the Hunt EDA to brush the dust off. There is no finer dry record cleaning method.