AmpsandSound Seneca Horn-Loaded Loudspeaker
- Product Code:
- Horn-Loaded Loudspeaker (Pair)
Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.
AmpsandSound Products Are Handmade In Small Batches and Go Through Extensive Quality Control
The Seneca is AmpsandSound's nod to studio monitors. Inspired by the flat response and dynamic range of the best studio monitors from TAD and JBL, the Seneca is a 2way horn loaded monitor. They’ve combined a massive 15” woofer for effortless bass and 2” beryllium compression driver provides for lighting fast transient, wide bandwidth and ultra-low distortion.
The Seneca like the Hudson is a partial horn-loaded loudspeaker system configured as an ultra-wide bandwidth 2way. The foundation of the Seneca is a direct radiating 15” woofer for low frequencies, providing usable bass into the 35hz range and crossing to the Mid-Horn @ 500hz. The Seneca mates a modern high-efficiency compression driver to Elliptical traxtrix horn. The reduction of a crossover point and driver increases coherence without sacrificing high frequency information. The concept of the Seneca is to have big horns, state of the art crossovers and drivers into the smallest form factor possible; and yielding bass response, efficiency, dynamic capabilities, low distortion, and scale of much larger designs in a much smaller enclosure.
The Seneca had long been utilized by ampsandsound’s founder in his personal system due to its more relaxed presentation. The core design was revisited with the development of the Hudson. Now paired with our newest crossover design and utilizing one of the most a calmed mid ranges, the Senenca was transformed into a loudspeaker capable of life like realism. Gone was the reference to a good sounding speaker, but now music was described as hearing the artist just feet away from you; as if you were at the counsel in the studio and they were playing to just you.
Its compact size makes it capable of being installed into even small most rooms, minimizes room interactions. Front ported and horn loaded reduces back wall interaction. The Seneca offers dynamic range, life like scale, tonal accuracy will appeal to audiophiles who desire all of the positive attributes of horn-loaded designs but without the issues of size and room interaction that are inherent to many designs.
The Seneca features a state of the art hand-wired crossover network, which utilizes high-order filters, and minimal driver lover lap, through use of large air-core inductors for low signal loss. If the heart of the Seneca is its horns and midrange, the crossover represents its cerebral cortex. The Seneca is art though design, providing detail rich rendering without coloration. Its crossover minimizes frequency overlap, and achieves phase coherence and perfect time alignment. Its crossover is hand-made and built to the same rigorous standards as our amplifiers and loudspeakers, utilizing Hyper-litz inductors and low Q capacitors. Each crossover weighs more than 15 pounds and is unlike anything you’ve seen or heard in horn-loaded loudspeakers.
The Seneca’s bass section utilizes a 15″ woofer in a direct-radiating configuration that is front-ported to minimize interaction with front walls. Through the use of FFT analysis, ampsandsound has carefully built an inert cabinet that features strategic bracing and dampening. As a result, the Hudson is capable of high output with minimal excursion, and greatly reduced levels of distortion over conventional designs.
The heart of the Seneca is its large CNC-cut midrange horn, which utilizes a hybrid tractrix flare, providing controlled horizontal dispersion and limiting vertical dispersion to reduce room interactions. The midrange horn is mated to a 2″ large-format midrange compression driver with beryllium diaphragm. No need for a tweeter with a midrange capable of extending past 20khz and providing a rule flat midrange. The combination of a large, precision-made wood horn with a large throat and large midrange compression driver has resulted in a midrange that is tonally accurate, yet rich with detail. The midrange is smooth, fast-sounding, and easy to listen to for hours.
34” H x 24” W x 16” D
125 lbs./per loudspeaker
Hand-wired crossover network utilizing high-order filters and large air-core inductors each crossover weighs more than eighteen pounds
15” Direct Radiating Woofer
2” large format midrange compression driver with beryllium diaphragm mated to CNC-cut midrange horn which utilizes a hybrid tractrix flare
Finish: Piano Black
Sophisticated hand-wired crossover network
High-order filters for minimal driver overlap
Large air-core inductors for low signal loss
Phase coherence and perfect time alignment
Utilizing Hyper-litz inductors and low Q capacitors
22lbs of crossover for each speaker
Frequency response: 34Hz – 20khz, -3dB, 99dB
Sensitivity: 100dB, 8 ohms, 1 watt/1 meter
Power handling: 200 watts/maximum
There are no reviews for this product.
Customers who bought AmpsandSound Seneca Horn-Loaded Loudspeaker, also bought:
There are no reviews for this product.