Pro-ject Authorized & Certified VPI Dealer

VINYL. OUR WAY OF LIFE SINCE 2004

(877) 929-8729
Site Search
Menu Free shipping on domestic orders over $49.99! - We ship worldwide!
20% Off Vinyl - LP20
Home > Products for: '

S Tonearm

'
  • 1
Results per page:
  • Pro-Ject Signature 12 Turntable 6 OPTIONS AVAILABLE Pro-Ject Signature 12 Turntable Quick View

    $12,000.00
    Buy Now
    x

    Pro-Ject Signature 12 Turntable


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    High-end audiophile turntable with fully adjustable 12 S-shaped tonearm, dampened sub-chassis, continuous speed control, and mass-loaded plinth


    The Signature turntable is Pro-Ject's all-out assault on the analog high-end.


    This no compromise approach to vinyl playback design commemorates Pro-Ject's 20-years as an esteemed manufacturer of turntables and electronics. Each table takes 3 months to build and is entirely constructed and assembled by a team of two highly skilled craftsman - truly an artisan product!


    Signature employs a highly sophisticated approach by combining the themes of mass loading and magnetic decoupling. The main plinth supports two plinths and two motors with a belt-driven flywheel system that is magnetically decouples the platter's bearing. The main plinth also houses the touch screen that allows control of all operational parameters and variable speed adjustment. The second plinth is made of aluminum sits beneath the platter and is responsible for supporting the magnetic suspension. Sorbothane Pillows isolate the entire assembly and further reduce unwanted disturbances and vibration. The flywheel belt-drive system employs two motors and ensures vibration and noise-free mechanical operation for all moving parts.


    The advanced single-pivot 12 tonearm can accommodate virtually any cartridge due to its wide range of adjustment possibilities and selection of different counterweights. It is even possible to adjust the VTA while the record is playing!


    Optional SuperPack includes Sumiko Palo Santos Presentation Cartridge at a significantly reduced price.


    Pro-Ject
    $12,000.00
    Signature 12 Turntable - 3 Colors Available - SuperPack Option
    Buy Now
  • AudioQuest Cougar Tonearm Cable (1.5m) AudioQuest Cougar Tonearm Cable (1.5m) Quick View

    $359.95
    Buy Now
    x

    AudioQuest Cougar Tonearm Cable (1.5m)


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.



    RCA to JIS


    With the addition of AudioQuest's patented Dielectric-Bias System, Cougar brings a level of low-level clarity and resolution rarely seen at this price. Perfect-Surface Copper+ is the icing on the cake, raising Cougar's performance significantly above Wildcat's.


    SOLID PERFECT-SURFACE COPPER+ CONDUCTORS (PSC+): Perfect-Surface Copper+ has an astonishingly smooth and pure surface. Proprietary metal-processing technology protects the wire's surface at every stage of drawing and fabrication. When high-purity low-oxide copper is kept as soft, pure and smooth as possible, it becomes a wonderfully low-distortion PSC+ conductor. PSC+ is manufactured by applying the same exceptional technology to an ultra-pure copper. The resulting sound quality is even more focused and simply less in the way. For over 30 years AudioQuest has pioneered the use of superior metals; yet even we were surprised by the huge leap in performance made possible with Perfect-Surface Technology. PSC+ simply outperforms all previously available copper metals at any price. All of Cougar's conductors are solid. Electrical and magnetic interaction between strands in a conventional cable is the greatest source of distortion, often causing a somewhat dirty, harsh sound. Solid conductors are fundamental toward achieving Cougar's very clean sound.


    FOAMED-POLYETHYLENE INSULATION: Any solid material adjacent to a conductor is actually part of an imperfect circuit. Wire insulation and circuit board materials all absorb energy (loss). Some of this energy is stored and then released as distortion. Cougar uses air-filled Foamed-Polyethylene Insulation because air absorbs next to no energy and Polyethylene is low-loss and has a benign distortion profile. Thanks to all the air in Foamed-PE, it causes much less of the out-of-focus effect common to other materials.


    DIELECTRIC-BIAS SYSTEM (DBS, US Pat #s 7,126,055 & 7,872,195 B1): All insulation slows down the signal on the conductor inside. When insulation is unbiased, it slows down parts of the signal differently, a big problem for very time-sensitive multi-octave audio. AudioQuest's DBS creates a strong, stable electrostatic field which saturates and polarizes (organizes) the molecules of the insulation. This minimizes both energy storage in the insulation and the multiple nonlinear time-delays that occur. Sound appears from a surprisingly black background with unexpected detail and dynamic contrast. The DBS battery packs will last for years. A test button and LED allow for the occasional battery check.


    CARBON-BASED 2-LAYER NOISE-DISSIPATION SYSTEM (NDS): 100% shield coverage is easy. Preventing captured RF Interference from modulating the equipment's ground reference requires AQ's Noise-Dissipation System. Metal and Carbon-Loaded synthetics prevent most RFI from reaching the equipment's ground plane.


    TERMINATIONS: Cougar's Cold-Welded Direct-Silver Plated RCA plugs use a proprietary design that eliminates the distortion caused by the extra contact inside most plugs. Because the ground shells are stamped instead of machined, the metal can be chosen for low distortion instead of machinability. A combination of these major ingredients, and many more subtle details add up to explain how Cougar can sound so clean, clear and dynamic.


    AudioQuest
    $359.95
    Tonearm Cable Buy Now
  • Ortofon MC Quintet Black S Ortofon MC Quintet Black S Quick View

    $999.00
    Buy Now
    x

    Ortofon MC Quintet Black S

    Ortofon


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    The Quintet Black S is the best example of Quintet's overall excellence


    The Quintet Black S is graced with a Nude Shibata diamond, considered one of the best stylus profiles available, mounted on a high-performance Sapphire cantilever.


    The Shibata's slim, highly polished profile allows an exceedingly wide contact area to the walls of the groove and ensures detailed and pure reproduction thoughout the spectrum, including even the most high frequency groove information.


    Top-mounting of the Quintet cartridges is easy and secure using the screws supplied. The aluminuim frame has threaded mounting holes and is fitted easily with the 5mm or 7mm screws depending on the thickness of the headshell.


    The Quintet series' right angles, straight lines, stylus visibility and ample distance between the record surface and the cartridge's bottom will make it easy to mount and align the cartridge and tonearm correctly. The Quintet Series gives excellent results with most common tonearms.

    Ortofon Cartridges
    $999.00
    Cartridge Buy Now
  • Pro-Ject Essential III Turntable 3 COLORS AVAILABLE Pro-Ject Essential III Turntable Quick View

    $299.00
    Buy Now
    x

    Pro-Ject Essential III Turntable



    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    The starter turntable of choice for audiophiles the world over!


    The new Essential III builds on the successes of the Essential II. The Essential II is a fabulous sounding turntable. It's the least expensive turntable on the market that includes both a high precision main bearing and a solid, adjustable tonearm that's based on the award winning Debut design. It's become the starter turntable of choice for audiophiles the world over.


    The new Essential III adds some nice upgrades compared to the Essential II. Cosmetically, the Essential III takes a cue from the award winning Debut Carbon DC, with a lustrous high-gloss finish that's available in Black, Red, or White. The platter also gets an upgrade: it's constructed of a dense MDF for minimal resonance and finished in a high-gloss piano black. The visual effect is striking, especially on the Red and White tables where the high-gloss platter contrasts nicely with the plinth. It looks really spectacular if you display it with some fun colored vinyl to accentuate the colors! The adjustable 8.6" one-piece aluminum tonearm is significantly more sophisticated than anything close to its price range, and utilizes sapphire bearings for minimal friction and many years of reliable performance. The Essential III also includes a factory mounted/aligned Ortofon OM10 cartridge. You won't find a better performing, better matched cartridge/tonearm combination in this price range.


    The main platter bearing is precision machined high grade stainless steel and the drive pulley is crafted from aluminum. A new DC motor speed controller board regulates the platter speed and the Essential III now includes Connect it E interconnect hardwired directly to the output.


    *Not compatible with Speed Box S or Speed Box DS.


    Pro-Ject
    $299.00
    Essential III Turntable - 3 Colors Available
    Buy Now
  • Pro-Ject Rolling Stones Debut Turntable 2 COLORS AVAILABLE Pro-Ject Rolling Stones Debut Turntable Quick View

    $449.00
    Buy Now
    x

    Pro-Ject Rolling Stones Debut Turntable



    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    SoundStageDirect U.S. Exclusive Retailer


    Extremely Limited!!


    Essential III. Debut Carbon drivetrain with 2-piece steel platter/nylon subplatter


    8.6" Aluminum Debut tonearm w Ortofon OM10 cartridge. Includes dust cover.




    Pro-Ject
    $449.00
    Rolling Stones Debut Turntable - 2 Colors Available
    Buy Now
  • Crosley C20A-ZE Two Speed Manual Turntable (On Sale) Crosley C20A-ZE Two Speed Manual Turntable (On Sale) On Sale Quick View

    $559.99$499.99Save $60.00 (11%)

    Buy Now
    x

    Crosley C20A-ZE Two Speed Manual Turntable (On Sale)


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    From the Crosley C-series, the C20 turntable has been designed and engineered with style and sound in mind. Crafted from audio-quality MDF and wrapped in genuine zebrano wood veneer, the minimalist plinth supports a solid semi-opaque acrylic platter and stands on three feet to keep vibrations at bay. The powerful belt-driven motor turns two speeds, 33rpm and 45rpm, to play both LPs and singles.


    The C20 is installed with a built-in phono-stage with USB output, useful for capturing favorite albums for the future. The S-shaped aluminum tonearm with sapphire bearings is equipped with an Ortofon OM10 Cartridge pre-mounted and adjusted. Tuning to taste has never been easier with adjustable tonearm counterweights and anti-skate adjustment. High-end features and timeless style meet in one classic turntable.


    Crosley
    $559.99 $499.99 Save $60.00 (11%)
    C20A-ZE Two Speed Manual Turntable Buy Now
  • Crosley K100 Stereo Turntable System (On Sale) Crosley K100 Stereo Turntable System (On Sale) On Sale Quick View

    $389.99$349.99Save $40.00 (10%)

    Buy Now
    x

    Crosley K100 Stereo Turntable System (On Sale)


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    Keep the music coming with the K100 two-speed, belt driven turntable stereo system. The balanced s-shaped tonearm offers hydraulic lift control, a lockable rest, and anti-skate technology, ensuring smooth playing. The sleek silver coating, as well as the 30 watt power amp speakers with Bluetooth connectivity, keep the K100 stylish and modern.



    Crosley
    $389.99 $349.99 Save $40.00 (10%)
    K100 Stereo Turntable System Buy Now
  • Crosley K200 Stereo Turntable System (On Sale) Crosley K200 Stereo Turntable System (On Sale) On Sale Quick View

    $469.99$419.99Save $50.00 (11%)

    Buy Now
    x

    Crosley K200 Stereo Turntable System (On Sale)


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    The K200 turntable stereo system is a contemporary choice. This direct driven turntable includes 30 watt power amp speakers with Bluetooth connectivity. The smooth s-shaped curve of the tonearm ensures getting in the groove with ease and plays two-speeds. The adjustable counterweight and adjustable pitch control, offer you command over the K200.



    Crosley
    $469.99 $419.99 Save $50.00 (11%)
    K200 Stereo Turntable System Buy Now
  • Pro-Ject RPM 1 Carbon Turntable 3 COLORS AVAILABLE Pro-Ject RPM 1 Carbon Turntable Quick View

    $499.00
    Buy Now
    x

    Pro-Ject RPM 1 Carbon Turntable


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    RPM 1 Carbon (with Sumiko Pearl) - Belt-driven turntable with 8.6 carbon fiber S-shaped tonearm and outboard motor


    This offering implements a radical concept that does not compromise sound quality at an entry-level price.


    RPM-1 Carbon utilizes a lot of innovations and enhancements: A low resonance chassis holds a newly designed inverted platter bearing with ceramic ball for further reduced rumble. An outboard 15V AC motor is smoothly driven using an ultra-precision AC generator with DC power supply for further enhanced speed stability. A completely new designed S-shaped tonearm tube is made from carbon fiber, aluminum and resin. Using a complex 3-step process with heat treatment and 100bar pressure, arm tube rigidity is strengthened, internal damping is maximized and resonances are reduced to a minimum. This makes the tonearm also suitable for MC cartridges. Additional features are a new magnetic antiskating mechanism and a TPE-damped counterweight. All ingredients add up to a miracle in sound for the price and ultra-stylish look!


    Pro-Ject
    $499.00
    RPM 1 Carbon Turntable - 3 Colors Available
    Buy Now
  • Pro-Ject RPM 3 Carbon Turntable 3 COLORS AVAILABLE Pro-Ject RPM 3 Carbon Turntable Quick View

    $999.00
    Buy Now
    x

    Pro-Ject RPM 3 Carbon Turntable



    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    RPM 3 Carbon (with Sumiko Blue Point No. 2) - Belt-driven turntable with 10 carbon fiber S-shaped tonearm and outboard motor


    RPM 3 Carbon utilizes evolutionary enhancements to improve the performance of RPM series: A low resonance chassis holds an inverted platter bearing with ceramic ball for further reduced rumble. An outboard 15V AC motor is smoothly driven using an ultra precision AC generator with DC power supply for further enhanced speed stability. A 10" S-shaped tonearm tube is made from carbon fiber, aluminium and resin. Using a complex 3-step process with heat treatment and 100bar pressure, arm tube rigidity is strengthened, internal damping is maximized and resonances are reduced to a minimum. This makes the tonearm also suitable for MC cartridges. Additional features are a magnetic anti-skating mechanism and a TPE-damped counterweight. All ingredients add up to a miracle in sound for the price and ultra-stylish look!




    Pro-Ject
    $999.00
    RPM 3 Carbon Turntable - 3 Colors Available
    Buy Now
  • Rega Planar 2 Turntable 6 OPTIONS AVAILABLE Rega Planar 2 Turntable Quick View

    $675.00
    Buy Now
    x

    Rega Planar 2 Turntable

    40th
    WhatThe


    Need help choosing the right turntable for you? Please contact our audio advisor at 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    The new Planar 2 was developed over the past two years alongside the recently released Planar 3. Featuring the brand new RB220 tonearm which is packed with groundbreaking new features.


    A new 24v, low noise motor, acrylic laminated plinth, newly designed central bearing and so much more. Every feature of this innovative new turntable is designed to extract the maximum amount of information and detail from your vinyl collection.
    Tonearm - Featuring the brand new RB220 tonearm which is packed with groundbreaking new features. Incorporating new ultra low friction, Rega designed, bespoke, zero play ball bearings (Patent Pending), housed within a brand new, stiffer and lightweight bearing housing which was developed with a new automatic bias setting negating the need for the user to set bias, making it almost completely plug and play apart from simple arm balancing. The new housing also includes an integrated arm clip and uses Rega's latest custom aluminium arm tube.


    Hub bearing - The Planar 2 has a new 11mm self securing brass bearing (Patent Pending) offering improved fit and less stress on the bearing preventing the transfer of potential energy.


    Plinth - High gloss acrylic laminated plinth, stiffer and vastly improved appearance with ergonomically positioned power switch. Two plinth finishes at launch: gloss black & gloss white


    Motor - New 24v low noise, low vibration motor assembly and new PCB.


    Platter - New float glass 'Optiwhite' 10mm - Improved accuracy platter.


    Other features :


    • Re-designed feet - New improved foot assembly to increase stability and reduce vibration transfer.
    • Carbon cartridge - supplied as standard on all Planar 2's for simple plug and play convenience.
    • Motor cover tray - with integrated cooling.
    • Optional lid / plinth protectors - supplied to prevent marks on the plinth and keep it looking its best.
    • Instructions - Easy to use multi-lingual quick start guide for easy set up.
    • Packaging - New improved packaging.


    The Performance Pack Kit Includes:


    • Rega-built Bias 2 MM cartridge
    • thick black 100% wool platter mat
    • reference drive belt (the white belt)

    Free installation of the Performance Pack upgrade is optional.


    Rega Turntables
    $675.00
    Planar Turntable - Black, White, Or Red - Performance Pack Option
    Buy Now
  • Pro-Ject Primary Turntable 2 COLORS AVAILABLE Pro-Ject Primary Turntable Quick View

    $249.00
    Buy Now
    x

    Pro-Ject Primary Turntable



    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    Audiophile "Plug & Play" turntable with easiest possible set-up and class-leading sound!


    It comes with an included dustcover and is pre-mounted with the capable Ortofon OM 5E moving magnet cartridge. The silicone drive belt along with a low-vibration synchronous motor is powered by an onboard DC to AC generator to ensure silent motor operation. The 8.6 aluminum tonearm with sapphire bearings is terminated with a gold-plated RCA cable for accurate and precise audio signal transmission. The low resonance platter features a stainless steel spindle and a brass bushing with a low-friction Teflon layer to virtually eliminate any bearing noise. Pro-Ject's Primary turntable take your vinyl playback to the next level without cleaning out your wallet. Available in matte Black or White.


    Pro-Ject
    $249.00
    Primary Turntable - 2 Colors Available
    Buy Now
  • Crosley C100A-SI Turntable (On Sale) Crosley C100A-SI Turntable (On Sale) On Sale Quick View

    $199.99$179.99Save $20.00 (10%)

    Buy Now
    x

    Crosley C100A-SI Turntable (On Sale)


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    Take a turn with the new Crosley C100. The adjustable counterweight and smooth s-shaped curves of the aluminum tonearm will get in the groove with ease. Get flashy with the adjustable strobe pitch control, and with a built-in pre-amp, the C100 is ready to rock with any powered speaker system.


    Step up to the next stage of the vinyl experience. High tech features and a sleek metallic body bring this analog player back to the future.


    Amp it Up


    The C100 is loaded with a built in preamp, so out of the box it's ready to blast with powered speakers. Or, plug your own preamp in and flip a switch to have music on your terms. (And tones.) Speakers plug in with RCA output ports, so you can customize your total music experience.


    Built for Sound


    Hi-tech, ABS construction gives the C100 a sleek, solid foundation. A modern transparent lid can be lifted up to control the tunes, or shut to protect records and wandering hands from messing with careful adjustments.


    Belt Up


    Using a belt-driven mechanism lets the C100 turn at two speeds to play 33RPM LPs, and 45RPM singles. There's even a 45 adapter, so you're covered at either speed.


    Get the Point


    The C100 comes equipped with a diamond-tipped Audio Technica needle to pick up every detail of every cut.


    Perfect Pitch


    Adjustable pitch control uses a strobe light beaming onto the platter dots to tame those finicky albums that tweak high or low, giving each note optimum sound.


    No Skate Zone


    This curvy s-shaped tonearm is not going to have any of this skating nonsense, preserving your sound, and your precious records.


    Crosley
    $199.99 $179.99 Save $20.00 (10%)
    C100A-SI Turntable Buy Now
  • Ortofon Alignment Tool Ortofon Alignment Tool Quick View

    $11.00
    Buy Now
    x

    Ortofon Alignment Tool

    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    Cartridge Alignment Tool/Cartridge Protractor


    An alignment protractor is used to find the correct distance from stylus tip to tonearm pivot.


    When aligning a cartridge for tangency using the alignment protractor, it is essential to remember that you are attempting to align the cantilever (and, hence, the stylus), not the cartridge body. There is no guarantee that the cantilever is perfectly aligned within the cartridge body, so simply aligning the cartridge body will not necessarily produce the desired result.


    Furthermore, many cartridge bodies have non-parallel sides, making tangential alignment of the cartridge body with the lines of tangency on the gauge virtually impossible.


    An alignment protractor is a plastic template onto which are printed the null point(s) and lines of tangency against which the cartridge should be aligned. The template is placed over the turntable's spindle (made possible via a spindle-sized hole drilled in the template) and placed against the platter.


    Cartridge must be adjusted until the cantilever is parallel to the set of parallel lines. And this should be achieved for both the indicated points. When the cartridge's longitudinal axis is parallel with the horizontal lines, tracking error will be at a minimum.

    Ortofon Cartridges
    $11.00
    Alignment Tool Buy Now
  • Crosley C200A-BK Direct Drive Turntable (On Sale) Crosley C200A-BK Direct Drive Turntable (On Sale) On Sale Quick View

    $279.99$249.99Save $30.00 (11%)

    Buy Now
    x

    Crosley C200A-BK Direct Drive Turntable (On Sale)


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    With more control than ever over the speed of your discs, this sleek, powerful turntable was built to mix it up. Spin into the next generation of the vinyl revolution with the Crosley C200, mixing Crosley's vintage-inspired, synth style with high tech, hi-end features.


    Warp Drive


    Crosley's first direct drive turntable motor brings records up to speed quickly and smoothly. Rock the built-in preamp, or bring your own into the mix to make the greatest mashup ever.


    On Point


    The C200 is equipped with a sharp Audio-Technica magnetic cartridge, adjusted to perfection. Or, choose your own beat with another cartridge and balance the sweet curves of the s-shaped tonearm with adjustable counterweights.


    Line In, Line Out


    This turntable was designed with mad style, sleek lines and cool technical details that are as functional as they are awesome to look at. The clear plastic case can even play with the lid shut, so that partying won't bump (and grind!) your precious records.


    Crosley
    $279.99 $249.99 Save $30.00 (11%)
    C200A-BK Turntable Buy Now
  • The Ultimate Analogue Test LP The Ultimate Analogue Test LP Quick View

    $39.99
    Buy Now
    x

    The Ultimate Analogue Test LP

    Editors Editors Editors Editors


    Analogue Productions set out to produce the ultimate test record.


    We've consulted many experts in the field, including mastering engineers, audio experts, turntable experts and audiophile listeners, to create a test record that's never been made before. When Barry Wolifson from Sterling Sound in New York City called us with the same idea we had been thinking about - that being to create the ultimate test record - he and our audio expert Clark Williams began to brainstorm and research ideas until they were both completely satisfied with what should go on the record.


    Most of the test records in the past have been made to test a variety of equipment. This test record excludes silly cannon shots, typewriters, voices on one channel and other useless fluff. This one specifically addresses your turntable and cartridge. It's designed to provide the basic test signals necessary to calibrate a turntable or cutting lathe as simply as possible. Most of the signals have specific implications, but it is certainly possible to use them in any number of novel ways.


    This record was mastered and cut on a Neumann VMS 80 lathe at Sterling Sound and pressed at Record Technology, Inc. on high-quality, 180-gram virgin vinyl.


    Side 1

    General Reference Level

    This 1 kHz reference tone will allow you to establish a "base level" for all measurements.
    Track 1 1Khz reference tone 7cm/s Mono, in phase (Lateral)

    Basic reference for all measurements, adjust meter for maximum convenience (in the studio 0VU).
    Adjust preamp channel balance for equal output.
    Also used to check the offset angle of the photo cartridge; L&R signals should be exactly in phase as displayed on an oscilloscope.


    Azimuth Adjustment

    Track 2 1kHz reference level Left channel only

    Measure Right channel output.

    Track 3 1kHz reference level Right channel only

    Measure Left channel output.

    The object is to sit the stylus exactly perpendicular in the groove.

    Twist cartridge about its radial axis until the measurements from Track 2 and Track 3 are equal or very close to equal for both channels.


    High Frequency Adjustment

    Tracks 4, 5 and 6 are used to calibrate the RIAA high frequency equalizer of a phono preamp. This will be used to calibrate a mastering lathe's phono preamplifier or any phono preamplifier that has these adjustments.

    Track 4 1 kHz tone at -20 below reference level, Lateral

    Reference for High Frequency test.

    Track 5 10 kHz reference tone at -20dbu, Lateral
    Adjust the high frequency until the output level equals that of Track 4.

    Track 6 1 kHz to 20 kHz sweep at -20dbu, Mono (Lateral)

    The AC millivoltmeter reading should stay constant across all frequencies. There are a number of factors which can affect frequency response, including cable capacitance, cartridge loading, tracking force and worn parts. Because of this, it can be difficult to achieve perfectly flat frequency response. Sometimes by making small compromises in the 10 kHz adjustment, a better overall frequency response can be achieved.


    Low Frequency Adjustment

    Tracks 7 & 8 are used to calibrate the RIAA low frequency equalizer of a phono preamp.

    Track 7 1 kHz to 20 Hz sweep at 0 VU (Lateral)

    Play Track 7 and measure the output with your AC millivolt meter.

    Ideally, the output will be flat across all frequencies. When viewed on an oscilloscope, the amplitude would remain constant during the frequency downsweep.

    Track 8 100 Hz reference tone at 0 vu (Lateral)
    Adjust LF Eq to reference (which is your reading from Track 1).


    Track 9 VTA adjust

    This is an IEC intermodulation distortion (IMD) test signal; 60Hz & 4kHz 4:1 ratio.

    Using an IMD tester, adjust VTA by raising or lowering the tonearm for minimum distortion.


    Track 10 Standard Wow & Flutter test signal; 3150Hz
    The Wow & Flutter meter will give dynamic speed variations as a percentage deviation from nominal.

    Also, the frequency counter should read exactly 3150 Hz for nominal speed. You can use the Hz function on your multi-meter (if so equipped) to verify speed here as well. You can also use to find the measurements at 45RPM. The correct reading at 45RPM would be 4253 Hz (45/33.33) x 3150.


    Side 2

    Track 1 Anti-skating test; 315Hz amplitude sweep to +12dbu (Lateral)

    Signal should remain clean in both channels up to the highest level, both audibly and as viewed on an oscilloscope. In case of distortion, increase anti-skating force or decrease anti-skate until breakup occurs equally in both channels. The left channel information is inscribed on the inner groove wall, the right channel information, on the outer groove wall. Because of the offset angle of a pivoted tonearm, a constantly varying vector force biases the arm towards the center of the record causing the stylus to lose contact with the outer (i.e. right channel) groove wall. Both linear and modulated groove velocity, tracking force, stylus profile, and vinyl composition are contributing factors. The anti skating force attempts to ameliorate this by applying an opposing similar force.

    It is also accepted that the overall force vector increases as the tonearm approaches closer to the spindle or end of the record.


    Track 2 Pink noise lateral

    Track 3 Pink noise vertical

    Used for cartridge "demagnetizing"

    You can also use this track to loosen up the cantilever's suspension to help break in a new cartridge. Play these tracks five to ten times after every 300 hours of normal LP playback.


    Track 4 1kHz @ reference level, vertical
    This out-of-phase signal should cancel to nothing when summed to mono.

    Any signals still present are distortion artifacts, lack of channel balance, or timing (phase) anomalies. This test can be a second confirmation of anti-skate adjustment.


    Track 5 1kHz to 10Hz sweep @ -20 below

    reference level, vertical
    Resonance anomalies in the tonearm / cartridge interface will show up as amplitude peaks and dips as the frequency sweeps down.

    Once again, by listening in 'Mono' it is easier to hear the distortion artifacts.


    Track 6 Silent groove for bearing rumble and table isolation

    During playback of this track, nothing should be transmitted from the turntable to the speakers. Replay the track and gently tap on the rack or base that the turntable is resting on. There should be little or no thump transferred to the speakers. This track will help you experiment with turntable isolation methods and products to be able to get the most out of your playback system. You may want to use a closed or sealed headphone for best listening results, or a stethoscope on the plinth.


    This title is not eligible for discount.

    Analogue Productions
    $39.99
    180 Gram Audiophile Virgin Vinyl LP - Sealed Buy Now
  • Rega RP10 Turntable (No Cartridge) Rega RP10 Turntable (No Cartridge) Quick View

    $5,495.00
    Buy Now
    x

    Rega RP10 Turntable (No Cartridge)

    40th



    Rega Made


    Need help choosing or installing your phono cartridge? Please contact our audio advisor at 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    **All Cartridges Installed Free Of Charge**


    The Rega RP10 skeletal turntable.


    Rega is extremely pleased to announce the launch of the much awaited RP10.


    Rega's design philosophy extends further than ever before with advanced components built around our radical new plinth design. Featuring the brand new RB2000 tonearm, a ceramic flywheel effect platter and the custom RP10 power supply (allowing total control and accuracy over both motor vibration and speed performance) guarantee the highest level of performance from a Rega turntable to date.


    The RP10 will also be available with its perfect partner, the Apheta moving coil cartridge, factory fitted as a package option.


    The Evolution of Revolution


    Evolution is a well proven and documented process in many areas of our lives. This applies in particular to design engineers and machines. Over the past forty years our cars have become more reliable and economical whilst we take for granted the reliability and speed of modern aircraft. Rega is no exception to evolution. Rega's experience and previous achievements allow us to continually develop and produce better products.


    The RP10 represents probably the biggest step forward in the evolution of Roy Gandy's turntable design philosophies. Low mass, high rigidity plinths combined with electronically controlled low vibration motors, high flywheel effect platters and lower mass higher stability tonearms.


    RP10 Custom power supply


    Housed in Rega's custom design case is a brand new advanced anti vibration and speed control circuit dedicated to running the 24v low noise motor. The speed and control of the motor is achieved by using a new DSP (digital signal processing) generator built upon a high stability crystal. The device will divide the accurate square wave from the crystal to the exact frequency required to turn the platter at the selected speed. The DSP core will also generate a near perfect sinusoidal waveform to power the motor. Factory set vibration and speed adjustments are then made to the power supply to tune the motor for optimal performance.


    The entire tonearm structure is designed to have the minimum of mechanical joints whilst using the stiffest materials in all critical areas. The tolerance of the RB2000 tonearm is so tight that no adhesive is used at any point throughout the construction. A brand new low mass, precision engineered, vertical bearing assembly has been manufactured to further compliment the inherent design philosophy of the RP10 turntable.


    The RB2000 uses the latest award winning Rega arm tube. Each one which is meticulously hand polished (keeping mass to an absolute minimum) and has been completely redesigned to redistribute mass and further reduce stresses and resonances. This advanced design tube increases the stiffness and rigidity of the overall assembly whilst reducing stress on the bearings even further.


    Magnesium and Phenolic - Dual bracing


    A super lightweight plinth combined with a double brace mounted specifically where the increased rigidity is required (between the tonearm mounting and the main hub bearing) forms a structurally sound "stressed beam" assembly. This design prevents energy absorption and unwanted resonances which will add un-natural distortions to the music. The RP10 takes our double brace technology to the next level. Not content with an unprecedented stiffness to mass ratio, Rega have obsessively reduced any resonant properties by using two different materials for the new stressed beam. The top layer is magnesium and the bottom layer is pheno-lic (two of the lightest and stiffest materials available). Incorporating two different materials into the brace structure lowers their ability to pick up unwanted airborne vibrations. Simply put, different materials have different natural resonances. By using two different materials together they decrease the natural frequency of each other by self damping.


    Super flywheel effect ceramic platter


    The RP10 uses a custom ceramic flywheel effect platter. The platter is produced from ceramic oxide powder which is compressed, fired and diamond cut to ensure perfect accuracy and flatness across the surface. The new platter features a modified construction over the previous P9 version with improved coupling to the sub platter.


    24V Low noise motor


    The motor is a high specification, 24V twin phase synchronous unit. It is controlled by Rega's unique and innovative RP10-PSU power supply. The motor drives the CNC machined pulley, sub platter and hub-bearing assembly via the twin belt drive. Each motor is individually hand tuned to its own custom power supply in the factory to minimise vibration, motor noise and ensure optimum performance.


    Skeletal plinth design with polyolefin foam core


    Controversially Rega has always researched methods of producing light but stiff and rigid plinths. The technology is simple: unwanted noise at microscopic levels is developed by the turntable motor and main bearing. The plinth can also pick up airborne vibration from the music. From the beginning in the 1970's Rega pioneered the use of a stressed skin structure for the plinth. This uses two layers of phenolic resin with a lightweight particle or fibre board sandwiched between the skins. This technique has been used in many applications where stiff, light structures are needed such as an aircraft wing or a Formula 1 chassis.


    The current increase in interest in turntables has allowed Rega to research and develop higher technology structures for the customer who is happy pay a little more for higher sound quality. The all new RP10 turntable utilises a unique new stressed skin structure produced from thin phenolic skins sandwiching a featherweight nitrogen expanded, closed cell, polyolefin foam core. This material has been developed exclusively for Rega over a three year period. The RP10 plinth is 7 times lighter than the weight of the original Planar 3 plinth. Rega has added even more stiffness in the crucial area between the arm and the main bearing.


    De-coupled outer frame and dust cover


    A common problem for many skeletal design turntables is the inability to incorporate an effective dust cover into the design. We have constructed an outer frame that minimises contact between the inner and outer plinth. The only points of contact are three location devices on the feet which centralises the inner and outer plinths perfectly. This makes set-up extremely easy and allows the use of a dust cover. The RP10 can be used without the outer frame if so desired.


    Turntable design & mythology


    Today there are many approaches to Hi-Fi design which follow established and informed engineering or electronic principles. Amplifier and loudspeaker design has been well documented over the years with excellent technical publications. These subjects have been based on tried and tested acoustic criteria and many computer software programs now exist that enable a near amateur to design a passable working loudspeaker based on known acoustic and mathematical parameters.


    Enter turntable design: When it comes to turntable design we are limited to a few poorly informed articles describing only very limited aspects of design. This is a subject full of mythology. Designers propose theories that counter the basic laws of physics, use terminology that doesn't actually exist in the engineering world, build products that are more like beautiful sculptures than acoustic reproduction machines and sell items costing tens of thousands of pounds that hardly function as intended and often fail to work at all.


    For instance a very common myth is "the heavier the better" concept. Turntable bases weighing tens of kilograms are not uncommon. The reality is that the base actually needs to be as light as possible to prevent unwanted bearing and motor noise being transferred to the turntable or record. Platters also fall under a similar myth with many platter designs becoming so heavy that it is impossible to design a correctly functioning bearing (and some so light that anyone can hear the speed inconsistency). The turntable platter itself needs to be of enough weight to spin at a constant speed within the confines of the chosen bearing and motor drive system.


    Many amateur designers in any field choose one component in a design and try to achieve an extreme in size, weight and quality. They believe that by taking one theory to its extreme the design will become "perfect". The reality of all engineering, design (and life) is that perfection is not possible. Based on this reality, Rega's goal has always been to optimise a mixture of numerous "correct compromises" thus bringing the designer nearer to the unachievable goal of perfection.


    Rega Turntables
    $5,495.00
    Rega RP10 - No Cartridge Buy Now
  • Rega RP10 Turntable (With Cartridge) Rega RP10 Turntable (With Cartridge) Quick View

    $6,695.00
    Buy Now
    x

    Rega RP10 Turntable (With Cartridge)

    40th



    Rega Made


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    **All Cartridges Installed Free Of Charge**


    Factory Fitted With Apheta 2 Moving Coil Cartridge


    The Rega RP10 skeletal turntable.


    Rega is extremely pleased to announce the launch of the much awaited RP10.


    Rega's design philosophy extends further than ever before with advanced components built around our radical new plinth design. Featuring the brand new RB2000 tonearm, a ceramic flywheel effect platter and the custom RP10 power supply (allowing total control and accuracy over both motor vibration and speed performance) guarantee the highest level of performance from a Rega turntable to date.


    The Evolution of Revolution


    Evolution is a well proven and documented process in many areas of our lives. This applies in particular to design engineers and machines. Over the past forty years our cars have become more reliable and economical whilst we take for granted the reliability and speed of modern aircraft. Rega is no exception to evolution. Rega's experience and previous achievements allow us to continually develop and produce better products.


    The RP10 represents probably the biggest step forward in the evolution of Roy Gandy's turntable design philosophies. Low mass, high rigidity plinths combined with electronically controlled low vibration motors, high flywheel effect platters and lower mass higher stability tonearms.


    RP10 Custom power supply


    Housed in Rega's custom design case is a brand new advanced anti vibration and speed control circuit dedicated to running the 24v low noise motor. The speed and control of the motor is achieved by using a new DSP (digital signal processing) generator built upon a high stability crystal. The device will divide the accurate square wave from the crystal to the exact frequency required to turn the platter at the selected speed. The DSP core will also generate a near perfect sinusoidal waveform to power the motor. Factory set vibration and speed adjustments are then made to the power supply to tune the motor for optimal performance.


    The entire tonearm structure is designed to have the minimum of mechanical joints whilst using the stiffest materials in all critical areas. The tolerance of the RB2000 tonearm is so tight that no adhesive is used at any point throughout the construction. A brand new low mass, precision engineered, vertical bearing assembly has been manufactured to further compliment the inherent design philosophy of the RP10 turntable.


    The RB2000 uses the latest award winning Rega arm tube. Each one which is meticulously hand polished (keeping mass to an absolute minimum) and has been completely redesigned to redistribute mass and further reduce stresses and resonances. This advanced design tube increases the stiffness and rigidity of the overall assembly whilst reducing stress on the bearings even further.


    Magnesium and Phenolic - Dual bracing


    A super lightweight plinth combined with a double brace mounted specifically where the increased rigidity is required (between the tonearm mounting and the main hub bearing) forms a structurally sound "stressed beam" assembly. This design prevents energy absorption and unwanted resonances which will add un-natural distortions to the music. The RP10 takes our double brace technology to the next level. Not content with an unprecedented stiffness to mass ratio, Rega have obsessively reduced any resonant properties by using two different materials for the new stressed beam. The top layer is magnesium and the bottom layer is pheno-lic (two of the lightest and stiffest materials available). Incorporating two different materials into the brace structure lowers their ability to pick up unwanted airborne vibrations. Simply put, different materials have different natural resonances. By using two different materials together they decrease the natural frequency of each other by self damping.


    Super flywheel effect ceramic platter


    The RP10 uses a custom ceramic flywheel effect platter. The platter is produced from ceramic oxide powder which is compressed, fired and diamond cut to ensure perfect accuracy and flatness across the surface. The new platter features a modified construction over the previous P9 version with improved coupling to the sub platter.


    24V Low noise motor


    The motor is a high specification, 24V twin phase synchronous unit. It is controlled by Rega's unique and innovative RP10-PSU power supply. The motor drives the CNC machined pulley, sub platter and hub-bearing assembly via the twin belt drive. Each motor is individually hand tuned to its own custom power supply in the factory to minimise vibration, motor noise and ensure optimum performance.


    Skeletal plinth design with polyolefin foam core


    Controversially Rega has always researched methods of producing light but stiff and rigid plinths. The technology is simple: unwanted noise at microscopic levels is developed by the turntable motor and main bearing. The plinth can also pick up airborne vibration from the music. From the beginning in the 1970's Rega pioneered the use of a stressed skin structure for the plinth. This uses two layers of phenolic resin with a lightweight particle or fibre board sandwiched between the skins. This technique has been used in many applications where stiff, light structures are needed such as an aircraft wing or a Formula 1 chassis.


    The current increase in interest in turntables has allowed Rega to research and develop higher technology structures for the customer who is happy pay a little more for higher sound quality. The all new RP10 turntable utilises a unique new stressed skin structure produced from thin phenolic skins sandwiching a featherweight nitrogen expanded, closed cell, polyolefin foam core. This material has been developed exclusively for Rega over a three year period. The RP10 plinth is 7 times lighter than the weight of the original Planar 3 plinth. Rega has added even more stiffness in the crucial area between the arm and the main bearing.


    De-coupled outer frame and dust cover


    A common problem for many skeletal design turntables is the inability to incorporate an effective dust cover into the design. We have constructed an outer frame that minimises contact between the inner and outer plinth. The only points of contact are three location devices on the feet which centralises the inner and outer plinths perfectly. This makes set-up extremely easy and allows the use of a dust cover. The RP10 can be used without the outer frame if so desired.


    Turntable design & mythology


    Today there are many approaches to Hi-Fi design which follow established and informed engineering or electronic principles. Amplifier and loudspeaker design has been well documented over the years with excellent technical publications. These subjects have been based on tried and tested acoustic criteria and many computer software programs now exist that enable a near amateur to design a passable working loudspeaker based on known acoustic and mathematical parameters.


    Enter turntable design: When it comes to turntable design we are limited to a few poorly informed articles describing only very limited aspects of design. This is a subject full of mythology. Designers propose theories that counter the basic laws of physics, use terminology that doesn't actually exist in the engineering world, build products that are more like beautiful sculptures than acoustic reproduction machines and sell items costing tens of thousands of pounds that hardly function as intended and often fail to work at all.


    For instance a very common myth is "the heavier the better" concept. Turntable bases weighing tens of kilograms are not uncommon. The reality is that the base actually needs to be as light as possible to prevent unwanted bearing and motor noise being transferred to the turntable or record. Platters also fall under a similar myth with many platter designs becoming so heavy that it is impossible to design a correctly functioning bearing (and some so light that anyone can hear the speed inconsistency). The turntable platter itself needs to be of enough weight to spin at a constant speed within the confines of the chosen bearing and motor drive system.


    Many amateur designers in any field choose one component in a design and try to achieve an extreme in size, weight and quality. They believe that by taking one theory to its extreme the design will become "perfect". The reality of all engineering, design (and life) is that perfection is not possible. Based on this reality, Rega's goal has always been to optimise a mixture of numerous "correct compromises" thus bringing the designer nearer to the unachievable goal of perfection.


    Rega Turntables
    $6,695.00
    Rega RP10 - Apheta 2 Cartridge Buy Now
  • Prestige Series Blue Cartridge Prestige Series Blue Cartridge Quick View

    $125.00
    Buy Now
    x

    Prestige Series Blue Cartridge

    The Prestige (and upscale Reference) cartridges from Grado are the first released since the elder Grado's retirement, but they mark an evolution, not dramatic change, of the classic Grado style. There are three basic levels in the Prestige lineup: Black/Green, Blue/Red, and Silver/Gold. In each of these pairings, the latter model is the same as the former, but is able to meet more astringent test specifications. The Green, for instance, is taken from the top 15% of the Black models production.


    The newly redesigned Blue1 and Red1 have had their coil design reconfigured, and the effective moving mass of their generating system has been reduced by 17%. The Blue1 and Red1 models use a four piece OTL cantilever technology, standard oxygen free wire in the coils and Grado's specially designed elliptical diamond mounted on a brass bushing. The Red1 model is selected from the Blue1 production run and meets higher test specifications. Approximately 10% of the production run will meet these standards and become Red1 models.


    All Grado Prestige cartridges have a fixed magnet and coils that generate a flux field axial pivot. A small generator disc is attached to the back end of the cantilever and moves within the lines of flux of the four coils and magnet generating a signal in response to stylus movement. The user-replaceable, elliptical diamond stylus is attached to the cantilever and moves within the four separate magnetic gaps which comprise what Grado calls a "flux-bridger" generator system. The generating element creates a flux increase in one gap while decreasing it in another to reduce distortion. According to Grado's literature, this design requires fewer coil turns, resulting in lower cartridge mass and electrical inductance. The cartridge is said to be insensitive to tonearm cable capacitance. The Grado cartridges are hand-built in the U.S.,and each cartridge is tested against Grado's standard for performance.


    Frequency Response: 10-55

    Principal: MI

    Channel Separation at 1KHz: 30

    Input Load: 47K

    Output at 1KHz 5CM/Sec.: 5mV

    Recommended Tracking Force: 1.5

    Stylus Type: E

    Inductance: 45mH

    Resistance: 475

    Compliance CUs: 20

    Stylus Replacement F: U

    Mounting: S/P

    Weight: 5.5




    This product is not eligible for discount.

    Grado Cartridges
    $125.00
    Cartridge Buy Now
  • Pro-Ject 1Xpression Carbon Classic Turntable 4 COLORS AVAILABLE Pro-Ject 1Xpression Carbon Classic Turntable Quick View

    $999.00
    Buy Now
    x

    Pro-Ject 1Xpression Carbon Classic Turntable



    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    Classic turntable with superior tone-arm & advanced magnetic cartridge reaches magical performance levels!


    1Xpression Carbon Classic is the 6th generation of the hi-fi classic Pro-Ject 1, which was presented for the first time in 1991.
    No other entry-level turntable concept is more audiophile and the current version includes a totally new carbon tone-arm with spin-off „EVO"-technology. It`s new innovative gimbal design features a resonance damping counterweight, that allows best performancefor any cartridge. The approved belt drive design offers low noise AC motor with effective motor decoupling, ultra precision frequencyDC-driven AC generator (like Speed Box) for ultimate speed stability.


    The complex main platter construction cannot befound elsewhere in this price range and is similar to the Xtension models. Advanced thermo plastic elastomers (TPE) are used in asandwich construction with aluminium alloy for optimised resonance behaviour. Platter bearing axle is made from lowtolerance chrome plated stainless steel running on Teflon bottom in a bronze bearing housing. Turntable main plinth is from lowresonance MDF, which effectivly is decoupled from structure-born noise by special absorber feet, that use TPE technology. As aspecial feature, this package comes with the outstanding 2M silver cartridge, which features silver spools for ultimate fidelity.


    Beside it's class-leading sound quality, this turntable convinces with classic elegance and four first-class finish options.


    *Not compatible with Speed Box S or Speed Box DS.


    Pro-Ject
    $999.00
    1Xpression Carbon Classic Turntable - 4 Colors Available
    Buy Now
  • MMF-1.5 Turntable MMF-1.5 Turntable Quick View

    $399.00
    Buy Now
    x

    MMF-1.5 Turntable


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    From the first music note to the final fade-out, the Music Hall mmf-1.5 sets your world to groove and your feet to dance.


    The stunning mmf-1.5 with its superior s-shaped alloy tonearm, Music Hall Melody cartridge, 3-speed belt drive design, and built-in phono pre-amp is a beautifully refined piece.


    Music Hall Turntables
    $399.00
    MMF-1.5 - With Cartridge & Built-In Phono Amp Buy Now
  • Crosley CR6250A-BK Keepsake Deluxe Portable and Adjustable USB Turntable (On Sale) Crosley CR6250A-BK Keepsake Deluxe Portable and Adjustable USB Turntable (On Sale) On Sale Quick View

    $199.99$169.99Save $30.00 (15%)

    Buy Now
    x

    Crosley CR6250A-BK Keepsake Deluxe Portable and Adjustable USB Turntable (On Sale)


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    Take the portability and charm of Crosley's suitcase-style turntable, combine it with high-end features and stellar performance, and bam! You've got the Keepsake Deluxe. Powerful but easy-to-use, this awesome turntable offers a built-in pre-amp or the chance to use your own, a sharp Audio Technica moving magnetic cartridge carried by a slick S-shaped tonearm. Adjustable counterweights and pitch control will keep music in line and the needle on point. All of this, neatly stashed in a beautiful vintage-inspired package.




    Crosley
    $199.99 $169.99 Save $30.00 (15%)
    CR6250A-BK Keepsake Deluxe Portable and Adjustable USB Turntable Buy Now
  • Pro-Ject 1Xpression Carbon Turntable Pro-Ject 1Xpression Carbon Turntable Quick View

    $799.00
    Buy Now
    x

    Pro-Ject 1Xpression Carbon Turntable


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    Classic turntable with superior tone-arm reaches magical performance levels!


    1Xpression Carbon is the 6th generation of the hi-fi classic Pro-Ject 1, which was presented for the first time in 1991. No other entry-level turntable concept is more audiophile and the current version includes a totally new carbon tone-arm with spin-off „EVO"-technology. It has new innovative gimbal design features a resonance damping counterweight, that allows best performance for any cartridge. The approved belt drive design offers low noise AC motor with effective motor decoupling, ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability. The complex main platter construction cannot be found elsewhere in this price range and is similar to the Xtension models. Advanced thermo plastic elastomers (TPE) are used in a sandwich construction with steel alloy for optimized resonance behavior. Platter bearing axle is made from low tolerance chrome plated stainless steel running on a Teflon bottom in bronze bearing housing. Turntable main plinth is made from low resonance MDF, which effectively is decoupled from structure-born noise by special absorber feet, that use TPE technology. Beside it`s class-leading sound quality, this turntable convinces with classic elegance and high-class black piano finish.


    Pro-Ject
    $799.00
    1Xpression Carbon Turntable Buy Now
  • Pro-Ject Xtension 12 Evolution Turntable 6 OPTIONS AVAILABLE Pro-Ject Xtension 12 Evolution Turntable Quick View

    $4,499.00
    Buy Now
    x

    Pro-Ject Xtension 12 Evolution Turntable


    Have a question about this product? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    Manual turntable with build in Pro-Ject Speed Box SE


    Pro-Ject's Xtension 12 incorporates over 20 years of experience in turntable design and manufacture. The Xtension 12 represents their latest technological efforts to address mass-decoupling and resonance reduction. Beginning with the mass-loaded magnetically floated sub-chassis and the precision balanced sandwich alloy platter (recycled vinyl/alloy), the foundation of this system weighs in at a super-heavy 55lbs. Additionally, Pro-Ject employs magnetic decoupling feet to thwart airborne or mechanical vibration from disturbing playback. This mass and isolation creates an environment of extremely low resonance allowing music to emerge from an ultra-silent black background. An AC motor with a two-step pulley drive with Electronic Speed Control maintains perfect pitch and rhythm resulting in inaudible wow, flutter and noise. There's even a built-in spirit level to assist setting the height-adjustable magnetic footers.


    Further reducing noise and vibration is the isolated Sorbothane mounting board for the 12 carbon-fiber tonearm. The conical arm and unified headshell are fabricated from a single piece of carbon fiber to avoid problems associated with standing wave reflections. Single screw fixing of the armtube allows for easy rotation for adjustment of needle azimuth. Additionally the arm is fully adjustable for VTA. A high-performance 123cm phono interconnect cable is included.


    Optional SuperPack includes Sumiko Blackbird Cartridge at a significantly reduced price.


    Pro-Ject
    $4,499.00
    Xtension 12 Evolution Turntable - 3 Colors Available - SuperPack Option
    Buy Now
  • 1
Go to top